BTS7811KDTMA1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-263-18 (15 Leads + 3 Tabs) |
| Number of Pins | 18 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| Series | TrilithIC™ |
| Feature | Status Flag |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 15 |
| ECCN Code | EAR99 |
| Applications | DC Motors, General Purpose |
| Technology | DMOS |
| Voltage - Supply | 1.8V~42V |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Number of Functions | 3 |
| Supply Voltage | 12V |
| Base Part Number | BTS7811 |
| Pin Count | 4 |
| JESD-30 Code | R-PSSO-G15 |
| Number of Outputs | 4 |
| Max Output Current | 42A |
| Interface | Logic |
| Nominal Supply Current | 8mA |
| Output Configuration | Half Bridge (2) |
| Halogen Free | Halogen Free |
| Voltage - Load | 1.8V~42V |
| Fault Protection | Open Load Detect, Over Temperature, Short Circuit, UVLO |
| Turn On Time | 220 μs |
| Output Peak Current Limit-Nom | 42A |
| Rds On (Typ) | 14m Ω LS, 26m Ω HS |
| Turn Off Time | 250 μs |
| Built-in Protections | TRANSIENT; OVER CURRENT; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SOURCE SINK |
| Load Type | Inductive |
| Length | 21.6mm |
| Width | 9.25mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
BTS7811KDTMA1 Overview
In this package, Tape & Reel (TR) is used.A cost-saving measure is taken to include H bridge in the TO-263-18 (15 Leads + 3 Tabs) package.With the 1.8V~42V supply voltage, improved reliabilbridge drivery can be achieved.H bridge circuit is mounted on Surface Mount.A normal operation of -40°C~150°C TJ is enabled by motor driver H bridges operating temperature.Among H bridge motor drivers many uses, H bridge motor driver can be found in DC Motors, General Purpose as well.The PCB is mounted wH gateh Surface Mount.Among full bridges specific characteristics is Status Flag.15 terminations are used to terminate transmission lines with H bridges that match their characteristic impedances.18 pins is used as pronged contacts as H bridge ic of a signal interface.In addition to the BTS7811 H bridge ic number, more related H bridge ics can be located by using its base H bridge ic number.There is a voltage supply of 12V that is used to operate H bridge circuit.Electronic H-bridges of the TrilithIC? series constitute this type of H-bridge.At a specified ambient temperature, 42A is the maximum load current that a power supply can provide.The 4 pins work together to provide this bridge driver with the functionality it requires.4 outputs are provided.
BTS7811KDTMA1 Features
Available in TO-263-18 (15 Leads + 3 Tabs) Package / Case
Operating Temperature at the range of Surface Mount
Interface IC Type : BTS7811
BTS7811KDTMA1 Applications
There are a lot of Infineon Technologies BTS7811KDTMA1 Full Bridge Drivers, Half-Bridge Drivers applications.
- High-Performance Gaming Motherboards
- High current, low profile DC-DC converters
- Bipolar stepper motor
- Optical disc drives
- Small Form-Factor Voltage Regulator Modules
- Voltage Regulators
- Voltage Regulators for CPUs
- Networking Microprocessor Voltage Regulators
- VTR
- Telecom Microprocessor
