Parameters |
Mounting Type |
Surface Mount |
Package / Case |
TO-263-8, D2Pak (7 Leads + Tab), TO-263CA |
Surface Mount |
YES |
Number of Pins |
7 |
Operating Temperature |
-40°C~150°C TJ |
Packaging |
Tape & Reel (TR) |
Published |
2006 |
Series |
NovalithIC™ |
Feature |
Latch Function, Slew Rate Controlled, Status Flag |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
7 |
ECCN Code |
EAR99 |
Applications |
DC Motors, General Purpose |
Additional Feature |
CONTAINS DC MOTOR DRIVER |
HTS Code |
8542.39.00.01 |
Subcategory |
Motion Control Electronics |
Technology |
DMOS |
Voltage - Supply |
5.5V~28V |
Terminal Position |
SINGLE |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
NOT SPECIFIED |
Number of Functions |
1 |
Supply Voltage |
18V |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
Base Part Number |
BTS7930 |
Pin Count |
4 |
Qualification Status |
Not Qualified |
Max Output Current |
50A |
Supply Voltage-Max (Vsup) |
28V |
Power Supplies |
8/18V |
Supply Voltage-Min (Vsup) |
5.5V |
Interface |
Logic |
Analog IC - Other Type |
BRUSHLESS DC MOTOR CONTROLLER |
Output Configuration |
Half Bridge |
Quiescent Current |
7μA |
Halogen Free |
Not Halogen Free |
Output Current per Channel |
20A |
Supply Current-Max (Isup) |
3mA |
Voltage - Load |
5.5V~28V |
Current - Output / Channel |
20A |
Fault Protection |
Current Limiting, Over Temperature, Short Circuit, UVLO |
Rds On (Typ) |
18m Ω LS, 10m Ω HS |
Load Type |
Inductive |
Width |
9.2mm |
RoHS Status |
RoHS Compliant |
Lead Free |
Contains Lead |
BTS7930B Overview
In this package, Tape & Reel (TR) is used.As a cost-saving measure, H bridge is included in the TO-263-8, D2Pak (7 Leads + Tab), TO-263CA package.Bridge driver is possible to ensure improved reliabilbridge drivery by varying the supply voltage of 5.5V~28V.H bridge circuit is mounted on Surface Mount.Motor driver H bridge works normally at -40°C~150°C TJ's operating temperature.There are a variety of applications for H bridge motor driver, including DC Motors, General Purpose.Full bridge also has a number of specific characteristics, including Latch Function, Slew Rate Controlled, Status Flag.It is possible to terminate a transmission line with a 7 termination using the H bridge which matches the characteristic impedance of the transmission line.Signal interfaces use 7 pins as pronged contacts.The base H bridge ic number of BTS7930 can be used to find related H bridge ics.There is a voltage supply of 18V that is used to operate H bridge circuit.H bridge circuit incorporates BRUSHLESS DC MOTOR CONTROLLER as its analog IC type.This is one of the types of electronic H-bridges in the NovalithIC? series.When the ambient temperature reaches 50A, the power supply will provide the maximum load current possible.A number of 4 pins work together to provide this bridge driver with its specific functions.H bridge motor drivers in the Motion Control Electronics subcategory have a number of similarities.8/18V supplies electrical power to the load.Additionally, H-bridge is capable of providing CONTAINS DC MOTOR DRIVER.
BTS7930B Features
Available in TO-263-8, D2Pak (7 Leads + Tab), TO-263CA Package / Case
Operating Temperature at the range of Surface Mount
Interface IC Type : BTS7930
With CONTAINS DC MOTOR DRIVER Drivers
BTS7930B Applications
There are a lot of Infineon Technologies BTS7930B Full Bridge Drivers, Half-Bridge Drivers applications.
- Dual DC motor
- CD players
- Small Form-Factor Voltage Regulator Modules
- DC-DC Converters
- PC peripherals
- Notebook Computers
- Voltage Regulators for CPUs
- DVD players
- Desktop Computers
- Networking Microprocessor Voltage Regulators