BU4051BCF-E2
| Parameters | |
|---|---|
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 10 |
| Base Part Number | BU4051 |
| Pin Count | 16 |
| Polarity | Non-Inverting |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 15μA |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 550 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Supply Type | Single |
| Bandwidth | 20MHz |
| Turn-Off Delay Time | 550 ns |
| Max Dual Supply Voltage | 9V |
| On-State Resistance (Max) | 160Ohm |
| Min Dual Supply Voltage | 1.5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 300nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF |
| On-state Resistance Match-Nom | 10Ohm |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 3V~18V |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e2 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 160Ohm |
| Terminal Finish | TIN COPPER |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 380mW |
| Technology | CMOS |
BU4051BCF-E2 Overview
Packed in 16-SOIC (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. High reliability is ensured by the advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. Multiplexer and demultiplexer circuits have a number 8:1. Temperatures around -40°C~85°C TA are extended for operation. In total, there have been 16 terminations. The electronic part delivers high-quality output through its 8 channels. When the electronic component is given a voltage of 5V, it should be turned on and run. As part of its design, the 16 series is equipped with this electronic component. There are 1 circuits in this multiplexer. If you are looking for variants of the digital switch, trying search with BU4051. This digital multiplexer has 160Ohm internal resistance. Please refer to the datasheets for 16 pins functions. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 18V. Analogue multiplexer with a Single supply type that is cost-effective. It is recommended to use 3V as the lowest voltage for the electrical part. For this digital switch to work, 15μA current would suffice. Draining from a single voltage supply, this analog switch requires a voltage of 3V~18V. For this multiplexer, dual supply voltage is feasible, but it should not exceed 9V. It is recommended that you attach at least 1.5V to your dual power supply. In 20MHz-bandwidths, data can be transferred.
BU4051BCF-E2 Features
8 Channels
15μA Supply Current
Bandwidth: 20MHz
BU4051BCF-E2 Applications
There are a lot of ROHM Semiconductor BU4051BCF-E2 Analog Switches & Multiplexers ICs applications.
- PDAs
- Cross Connects
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Central office
- Communication systems
- Remote wireless modules
- Isolation
- E1 Multiplexer
- Data switching
- SONET
