BU4051BCFV-E2
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-LSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e2 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 160Ohm |
| Terminal Finish | TIN COPPER |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 620mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 10 |
| Base Part Number | BU4051 |
| Pin Count | 16 |
| Polarity | Non-Inverting |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 15μA |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 550 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Supply Type | Single |
| Bandwidth | 20MHz |
| Turn-Off Delay Time | 550 ns |
| Max Dual Supply Voltage | 9V |
| On-State Resistance (Max) | 160Ohm |
| Min Dual Supply Voltage | 1.5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 300nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF |
| On-state Resistance Match-Nom | 10Ohm |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 3V~18V |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
BU4051BCFV-E2 Overview
Shipping overseas is convenient with the electronic component packed in 16-LSSOP (0.173, 4.40mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. 8:1 is the number of circuits in the multiplexer and demultiplexer. Extended operating temperature around -40°C~85°C TA. Total terminations are 16. The electronic part delivers high-quality output through its 8 channels. An 5V voltage supply should allow the electrical part to be turned on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. There are 1 circuits in this multiplexer. Look for analog switch ic variants by searching with BU4051. This digital multiplexer has 160Ohm internal resistance. The datasheets for the 16 pins explain the functions. There is Multiplexer or Switches analog multiplexer like this in the world. It is generally not recommended to supply a voltage higher than 18V to the switch device in normal circumstances. The analog switch ic is of the Single supply type and is cost-effective. A low voltage of 3V should be applied to the electronic component. An operating current of 15μA would be sufficient for this switch device. This analogue multiplexer requires a voltage of 3V~18V when it drains from a single voltage supply. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 9V. A dual power supply should have at least 1.5V voltage attached. 20MHz-bandwidths can be used to transfer data between multiplexers.
BU4051BCFV-E2 Features
8 Channels
15μA Supply Current
Bandwidth: 20MHz
BU4051BCFV-E2 Applications
There are a lot of ROHM Semiconductor BU4051BCFV-E2 Analog Switches & Multiplexers ICs applications.
- Switching Systems
- Multi-Line E1 Interface Cards
- Precision instrumentation
- High speed data transmission line cards
- SONET
- High-Voltage
- Data Acquisition Systems
- Microprocessor controlled systems
- Avionics test equipment
- Private Branch Exchange (PBX)
