BU4052BC

SP4T 160Ohm DUAL Analog Switches BREAK-BEFORE-MAKE BU4052 16 Pins 300nA 5V 16-DIP (0.300, 7.62mm)

Manufacturer: ROHM Semiconductor
Nocochips NO: 687-BU4052BC
Package: 16-DIP (0.300, 7.62mm)
Datasheet: PDF
Stock: 180
Description: SP4T 160Ohm DUAL Analog Switches BREAK-BEFORE-MAKE BU4052 16 Pins 300nA 5V 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Contact Plating	Copper, Tin
Mount	Through Hole
Mounting Type	Through Hole
Package / Case	16-DIP (0.300, 7.62mm)
Number of Pins	16
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2008
JESD-609 Code	e2
Pbfree Code	yes
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	160Ohm
Terminal Finish	TIN COPPER
Subcategory	Multiplexer or Switches
Technology	CMOS
Terminal Position	DUAL
Peak Reflow Temperature (Cel)	260
Number of Functions	1
Supply Voltage	5V
Time@Peak Reflow Temperature-Max (s)	10
Base Part Number	BU4052
Pin Count	16
Polarity	Non-Inverting
Power Supplies	5/15V
Number of Channels	4
Number of Circuits	2
Max Supply Voltage	18V
Min Supply Voltage	3V
Analog IC - Other Type	DIFFERENTIAL MULTIPLEXER
Operating Supply Current	15μA
Propagation Delay	15 ns
Turn On Delay Time	550 ns
Logic Function	Demultiplexer, Multiplexer
Supply Type	Single
Bandwidth	20MHz
Supply Current-Max (Isup)	0.015mA
Turn-Off Delay Time	550 ns
Max Dual Supply Voltage	9V
On-State Resistance (Max)	160Ohm
Min Dual Supply Voltage	1.5V
Multiplexer/Demultiplexer Circuit	4:1
Off-state Isolation-Nom	50 dB
Current - Leakage (IS(off)) (Max)	300nA
Channel Capacitance (CS(off), CD(off))	10pF
On-state Resistance Match-Nom	10Ohm
Switch Circuit	SP4T
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+)	3V~18V
Height Seated (Max)	4.55mm
Length	19.4mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

BU4052BC Overview

The electronic component is convenient to ship overseas because it is packed in a 16-DIP (0.300, 7.62mm). This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Through Hole position. In the multiplexer and demultiplexer, 4:1 represents the number of circuits. The operating temperature is extended to around -40°C~85°C TA. In total, there are 16 terminations. As a result of its 4 channels, this electronic component provides high-quality output. A 5V voltage supply should turn on and run the electronic component. A total of 16 pins are injected into the body of the electronic part. A SP4T switching circuit is used for these analog switches. There are 2 circuits in this multiplexer. Try searching with BU4052 if you're looking for variants. The internal resistance of this digital multiplexer is 160Ohm. The functions of 16 pins can be found in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. In normalcircumstances, users should not exceed 18V volts for the multiplexer. A analog switch ic that has a cost-effective Single supply type. 3V is the lowest voltage that should be fed to the electronic electronic part. This digital switch can be operated with a current of 15μA. A voltage of 3V~18V is required to drain this analog switch from a single voltage supply. If put voltage greater than 9V on the multiplexer, damage may be caused to the device. In the case of dual power supplies, you should connect at least 1.5V. A DIFFERENTIAL MULTIPLEXER analog IC is integrated into the board. 20MHz-bandwidths can be used to transfer data between multiplexers.