BU4052BCF-E2

SP4T 160Ohm DUAL Analog Switches BU4052 16 Pins 300nA 5V 16-SOIC (0.173, 4.40mm Width)

Manufacturer: ROHM Semiconductor
Nocochips NO: 687-BU4052BCF-E2
Package: 16-SOIC (0.173, 4.40mm Width)
Datasheet: -
Stock: 516
Description: SP4T 160Ohm DUAL Analog Switches BU4052 16 Pins 300nA 5V 16-SOIC (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.173, 4.40mm Width)
Number of Pins	16
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2008
JESD-609 Code	e2
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	160Ohm
Terminal Finish	TIN COPPER
Subcategory	Multiplexer or Switches
Max Power Dissipation	380mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	1
Supply Voltage	5V
Time@Peak Reflow Temperature-Max (s)	10
Base Part Number	BU4052
Pin Count	16
Polarity	Non-Inverting
Power Supplies	5/15V
Number of Channels	4
Number of Circuits	2
Max Supply Voltage	18V
Min Supply Voltage	3V
Analog IC - Other Type	DIFFERENTIAL MULTIPLEXER
Operating Supply Current	15μA
Propagation Delay	15 ns
Turn On Delay Time	550 ns
Logic Function	Demultiplexer, Multiplexer
Number of Inputs	8
Supply Type	Single
Bandwidth	20MHz
Supply Current-Max (Isup)	0.015mA
Turn-Off Delay Time	550 ns
Max Dual Supply Voltage	9V
On-State Resistance (Max)	160Ohm
Min Dual Supply Voltage	1.5V
Multiplexer/Demultiplexer Circuit	4:1
Off-state Isolation-Nom	50 dB
Current - Leakage (IS(off)) (Max)	300nA
Channel Capacitance (CS(off), CD(off))	10pF
On-state Resistance Match-Nom	10Ohm
Switch Circuit	SP4T
Voltage - Supply, Single (V+)	3V~18V
Height Seated (Max)	1.71mm
Length	10mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

BU4052BCF-E2 Overview

As the electronic part is packed in 16-SOIC (0.173, 4.40mm Width), international shipping is convenient. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. 4:1 is the number of circuits in the multiplexer and demultiplexer. Operational temperature extended around -40°C~85°C TA. 16 terminations have been made so far. A 4 channel electronic part produces high-quality output. Turning on and running the electrical part should be easy with a 5V voltage supply. A total of 16 pins are injected into the electrical part body. SP4T switching circuits are used in these analog switch ics. A total of 2 circuits make up this switch device. Try searching with BU4052 to find analog multiplexer variants. An switch multiplexer with 160Ohm internal resistance has a value of 160Ohm. Datasheets for 16 pin functions are available upon request. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 18V. Analogue multiplexers of the Single supply type that are cost-effective. It is recommended that the electrical component receives a voltage of 3V. It would be sufficient to run this analogue multiplexer with 15μA current. This analog switch requires a voltage of 3V~18V to drain from a single voltage supply. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 9V. For dual power supplies, a voltage of at least 1.5V should be attached. There is an integrated analog IC DIFFERENTIAL MULTIPLEXER in the module. The electrical component supports 8 inputs. The transfer of data can be performed over 20MHz bandwidths.