BU4053BC
| Parameters | |
|---|---|
| Supply Type | Single |
| Bandwidth | 20MHz |
| Supply Current-Max (Isup) | 0.015mA |
| Turn-Off Delay Time | 550 ns |
| Max Dual Supply Voltage | 9V |
| On-State Resistance (Max) | 160Ohm |
| Min Dual Supply Voltage | 1.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 300nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF |
| On-state Resistance Match-Nom | 10Ohm |
| Switch Circuit | SPDT |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 3V~18V |
| Height Seated (Max) | 4.55mm |
| Length | 19.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e2 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 160Ohm |
| Terminal Finish | Tin/Copper (Sn/Cu) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 10 |
| Base Part Number | BU4053 |
| Pin Count | 16 |
| Polarity | Non-Inverting |
| Power Supplies | 5/15V |
| Number of Channels | 2 |
| Number of Circuits | 3 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 15μA |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 550 ns |
| Logic Function | Demultiplexer, Multiplexer |
BU4053BC Overview
Due to its 16-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tube. Mounted in Through Hole is this multiplexer. Multiplexers and demultiplexers have a ratio of 2:1. Increasing operating temperature to around -40°C~85°C TA. The total number of terminations is 16. A high-quality output is provided by the electrical component's 2 channels. An 5V voltage supply should allow the electrical part to be turned on and run. A total of 16 pins are injected into the electrical part body. Circuits based on SPDT switching are used to construct these analog switch ics. 3 circuits are used in this analogue multiplexer. Try searching for BU4053 variants of the analog switch ic. Internally, this switch multiplexer has a resistance of 160Ohm. The datasheets for the 16 pins explain the functions. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage higher than 18V should not normally be supplied to the switches. Analog switch ics with Single supply type are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 3V. It would be sufficient to run this analogue multiplexer with 15μA current. A voltage of 3V~18V is required to drain this analog switch from a single voltage supply. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 9V. It is recommended that you attach at least 1.5V to your dual power supply. There are 20MHz bandwidths for data transfer.
BU4053BC Features
2 Channels
Switch Circuit: SPDT
15μA Supply Current
Bandwidth: 20MHz
BU4053BC Applications
There are a lot of ROHM Semiconductor BU4053BC Analog Switches & Multiplexers ICs applications.
- SONET
- Voice over IP/DSL – Integrated Access Devices, Smart
- Fiber to the Home
- Communication systems
- DSLAMs
- High reliability control systems
- MP3 players
- Channel Banks
- SDH/SONET multiplexers
- Cell phones
