BU4066BC
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e2 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 280Ohm |
| Terminal Finish | TIN COPPER |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.18W |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 10 |
| Base Part Number | BU4066 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Polarity | Non-Inverting |
| Power Supplies | 5/15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 4μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 140 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 140 ns |
| Max Dual Supply Voltage | 9V |
| On-State Resistance (Max) | 280Ohm |
| Min Dual Supply Voltage | 1.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 300nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF |
| On-state Resistance Match-Nom | 25Ohm |
| Switch Circuit | SPST - NO |
| Crosstalk | -50dB @ 1MHz |
| Voltage - Supply, Single (V+) | 3V~18V |
| Normal Position | NO |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
BU4066BC Overview
Due to its 14-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. The advanced packaging method Tube provides high reliability. In Through Hole, this analog switch is mounted. There is 1:1 ratio between the number of multiplexers and demultiplexers. Temperatures around -40°C~85°C TA are extended for operation. There are 14 terminations totally. High-quality output is provided by the electronic component's 1 channels. It is safe to turn on and run the electronic component with a 5V voltage supply. There is an electrical component included in the 14 series. The analog switch ics are built using SPST - NO switching circuits. There are 4 circuits in this switch device. Try searching for the analog switch ic with BU4066 if you are looking for variants. An switch multiplexer with 280Ohm internal resistance has a value of 280Ohm. You can find the functions of the 14 pins in the datasheets. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 18V in normal situations. An effective Single supply digital multiplexer. A low voltage of 3V should be applied to the electronic component. It would be sufficient to run this analogue multiplexer with 4μA current. This analogue multiplexer requires a voltage of 3V~18V when it drains from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA. Despite this switch device's dual supply capability, its voltage should not exceed 9V. With dual power supplies, you should attach at least 1.5V. The outputs of this digital multiplexer are SEPARATE OUTPUT in number.
BU4066BC Features
1 Channels
Switch Circuit: SPST - NO
4μA Supply Current
BU4066BC Applications
There are a lot of ROHM Semiconductor BU4066BC Analog Switches & Multiplexers ICs applications.
- HDTV
- Frame Relay Equipment
- Precision test equipment
- Battery Powered Systems
- Multi-Line E1 Interface Cards
- PDH Multiplexers
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Imaging
- Cellular phones
- High-Voltage
