BU4066BCFV-E2
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-LSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e2 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 280Ohm |
| Terminal Finish | TIN COPPER |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.18W |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 10 |
| Base Part Number | BU4066 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Polarity | Non-Inverting |
| Power Supplies | 5/15V |
| Number of Channels | 4 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 4μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 140 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 140 ns |
| Max Dual Supply Voltage | 9V |
| On-State Resistance (Max) | 280Ohm |
| Min Dual Supply Voltage | 1.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 300nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF |
| On-state Resistance Match-Nom | 25Ohm |
| Switch Circuit | SPST - NO |
| Crosstalk | -50dB @ 1MHz |
| Voltage - Supply, Single (V+) | 3V~18V |
| Normal Position | NO |
| Height Seated (Max) | 1.25mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
BU4066BCFV-E2 Overview
Shipping overseas is convenient with the electronic component packed in 14-LSSOP (0.173, 4.40mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. There is an analog multiplexer mounted in position Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, there are 14 terminations. A electrical component with 4 channels is capable of high-quality output. With a 5V voltage supply, the electrical component should be turned on and run. 14 pins are injected to the electronic part body. The analog switch ics are built using SPST - NO switching circuits. Try searching for the analog switch ic with BU4066 if you are looking for variants. As far as internal resistance is concerned, it has 280Ohm. For details about the functions of 14 pins, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Multiplexers should not be powered above 18V in normal situations. Analogue multiplexer with a Single supply type that is cost-effective. The lowest voltage fed to the electronic component should be 3V. In order to operate this switch device, it would need a current of 4μA. Analogue multiplexers require a 3V~18V voltage to drain from a single voltage supply. When the digital multiplexer is charged above 1μA, damage can occur. Despite this switch's dual supply capability, its voltage should not exceed 9V. For dual power supplies, a voltage of at least 1.5V should be attached. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
BU4066BCFV-E2 Features
4 Channels
Switch Circuit: SPST - NO
4μA Supply Current
BU4066BCFV-E2 Applications
There are a lot of ROHM Semiconductor BU4066BCFV-E2 Analog Switches & Multiplexers ICs applications.
- Data Acquisition Systems
- Avionics
- Signal routing between systems
- Fault Tolerant Systems
- Imaging
- Precision test equipment
- Video signal routing
- Automotive applications
- Power routing
- Multi-Line E1 Interface Cards
