banner_page

BU4S66G2-TR

SPST - NO 280Ohm DUAL Analog Switches BU4S66 5 Pins 300nA 5V SC-74A, SOT-753


  • Manufacturer: ROHM Semiconductor
  • Nocochips NO: 687-BU4S66G2-TR
  • Package: SC-74A, SOT-753
  • Datasheet: -
  • Stock: 557
  • Description: SPST - NO 280Ohm DUAL Analog Switches BU4S66 5 Pins 300nA 5V SC-74A, SOT-753(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Mounting Type Surface Mount
Package / Case SC-74A, SOT-753
Number of Pins 5
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2005
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 5
Termination SMD/SMT
Resistance 950Ohm
Subcategory Multiplexer or Switches
Max Power Dissipation 540mW
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Number of Functions 1
Supply Voltage 5V
Base Part Number BU4S66
Output SEPARATE OUTPUT
Pin Count 5
Number of Channels 1
Max Supply Voltage 18V
Min Supply Voltage 3V
Operating Supply Current 4μA
Power Dissipation 540mW
Max Supply Current 10mA
Throw Configuration SPST
Turn On Delay Time 80 ns
Supply Type Single
Turn-Off Delay Time 100 ns
On-State Resistance (Max) 280Ohm
Multiplexer/Demultiplexer Circuit 1:1
Current - Leakage (IS(off)) (Max) 300nA
Channel Capacitance (CS(off), CD(off)) 10pF
Switch Circuit SPST - NO
Voltage - Supply, Single (V+) 3V~18V
Max Junction Temperature (Tj) 150°C
Drain to Source Resistance 250Ohm
Normal Position NO
On-State Resistance 80Ohm
Height 1.25mm
Length 2.9mm
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status ROHS3 Compliant
Lead Free Lead Free

BU4S66G2-TR Overview


The electrical component comes in SC-74A, SOT-753 packaging, which makes it convenient to ship overseas. The advanced packaging method Tape & Reel (TR) provides high reliability. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 1:1. Temperatures around -40°C~85°C TA are extended for operation. In total, there are 5 terminations. By its 1 channels, the electronic component provides high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. There is an electrical component included in the 5 series. The analog switch ics are built using SPST - NO switching circuits. Use BU4S66 to search for variants of the digital switches. Internally, this switch multiplexer has a resistance of 950Ohm. For functions related to 5 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 18V. The digital multiplexer has a low cost Single supply. The lowest voltage fed to the electronic component should be 3V. For this digital switch to work, 4μA current would suffice. Using only a single voltage supply, this analog switch requires 3V~18V voltage. The analogue multiplexer may be damaged if voltage is greater than 10mA. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. A Drain to Source resistance of 250Ohm is shown for this electronic part.

BU4S66G2-TR Features


1 Channels
Switch Circuit: SPST - NO
4μA Supply Current
Drain-to-Source resistance: 250Ohm

BU4S66G2-TR Applications


There are a lot of ROHM Semiconductor BU4S66G2-TR Analog Switches & Multiplexers ICs applications.

  • Access Concentrators
  • Medical systems
  • Industrial and process control systems
  • Wireless Local Loop
  • Channel Banks
  • Signal routing between systems
  • Relay replacements
  • SONET
  • Fiber In The Loop (FITL)
  • Modems

Write a review

Note: HTML is not translated!
    Bad           Good