BUS1DJC0GWZ-E2
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 4-XFBGA |
| Number of Pins | 4 |
| Operating Temperature | -30°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2014 |
| Feature | Load Discharge, Slew Rate Controlled |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 4 |
| ECCN Code | EAR99 |
| Resistance | 245mOhm |
| Max Power Dissipation | 410mW |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | BUS1DJC0GWZ |
| Number of Outputs | 1 |
| Output Type | P-Channel |
| Max Output Current | 2A |
| Supply Voltage-Max (Vsup) | 5V |
| Interface | On/Off |
| Nominal Supply Current | 350mA |
| Output Configuration | High Side |
| Output Current | 2A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Turn On Delay Time | 32 μs |
| Switch Type | General Purpose |
| Nominal Input Voltage | 5V |
| Turn-Off Delay Time | 25 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 1.1V~5V |
| Output Peak Current Limit-Nom | 2A |
| Rds On (Typ) | 58m Ω |
| Built-in Protections | OVER CURRENT |
| Height Seated (Max) | 0.35mm |
| Length | 0.8mm |
| Width | 0.8mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
BUS1DJC0GWZ-E2 Overview
It is packaged in the form of a Tape & Reel (TR).The 4-XFBGA package contains it.A Surface Mount mounting is used for the LED driving board.General Purpose is the type of switch owned by it.It is recommended to set the temperature to -30°C~85°C TA in order to ensure reliable operation.The LED driver is equipped with 1 outputs.A supply voltage of Not Required is required for it to operate.It produces a maximum output voltage of P-Channel volts at its maximum output.In terms of features, the LED driving board has Load Discharge, Slew Rate Controlled.It comes under the family of BUS1DJC0GWZ.A total of 4 terminations have been found in it.The operation is performed through the 4 pins.It contains 1 functions.The maximum output current is reduced to 2A to meet the operation criteria.With a supply voltage of 3.3V, high efficiency is possible.The lighting driver is mounted in the direction of Surface Mount.In this case, there is 245mOhm resistance in the LED driving board.The output current is set to 2A in this case.The maximum supply voltage for this LED driver is 5V (Vsup).
BUS1DJC0GWZ-E2 Features
Supplied from 3.3V
Resistance of 245mOhm
BUS1DJC0GWZ-E2 Applications
There are a lot of ROHM Semiconductor BUS1DJC0GWZ-E2 Power Switches ICs applications.
- Portable GPS Device
- Solid State Drivers
- Storage Drives
- Wireless Modem Data Cards
- USB Power Distribution
- Hot Swap
- Low Voltage I/O System Power
- Portable Video Game Players
- Storage (HDDs, SSDs)
- Portable Music Players
