CAT150161MWI-GT3
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | EEPROMs |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | CAT15016 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 3/5V |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.5V |
| Operating Supply Current | 2mA |
| Max Supply Current | 2mA |
| Watchdog Timer | No |
| Reset | Active High |
| Voltage - Threshold | 4.38V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Halogen Free | Halogen Free |
| Memory Width | 1 |
| Min Reset Threshold Voltage | 4.31V |
| Max Reset Threshold Voltage | 4.45V |
| Standby Current-Max | 0.00002A |
| Undervoltage Threshold | 4.5V |
| Parallel/Serial | SERIAL |
| Write Cycle Time-Max (tWC) | 5ms |
| Data Retention Time-Min | 100 |
| Write Protection | HARDWARE |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | LAST SHIPMENTS (Last Updated: 1 week ago) |
| Mount | Surface Mount |
CAT150161MWI-GT3 Overview
A total of 8 terminals are used to mount this power management. There is a Tape & Reel (TR)-packaging method applied to IC management. Please find attached 1 functions for your reference in this IC power. IC management is packaged as a 8-SOIC (0.154, 3.90mm Width) package. There are a lot of similarities between this IC management and other Simple Reset/Power-On Reset products. Specifies a reflow peak temperature of 260 for the package during reflow. When a supply voltage of 5V is applied to the power ic, it conducts. During operation, the power ic is supplied with a voltage of 1. Power management is included in the Surface Mount mount. There is a subcategory called EEPROMs for this power management. It has a total of 8 pins that are attached to IC management. 8 pins are on the supervisor. In order for this PMIC to work correctly, the minimum supply voltage (Vsup) should be greater than 2.5V. There should be no more than 5.5V volts of supply voltage (Vsup) in this power management. Mounting type Surface Mount is recommended. You should set the supervisor's temperature during -40°C~85°C TA . The output voltage of this power managment ic during operation is Push-Pull, Totem Pole. As far as the supply current of the power management is concerned, it is 2mA. A similar IC managements number of the manufacturer can always be found by using CAT15016, the base power ics number. In order to operate this power management, it requires 3/5V volts of power. The maximum supply temperature voltage supervisor can handle is 2mA.
CAT150161MWI-GT3 Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 2.5V
2mA operating supply current
CAT150161MWI-GT3 Applications
There are a lot of ON Semiconductor CAT150161MWI-GT3 Voltage Supervisors applications.
- Telecommunications equipment
- Important electronics for automotive protection
- Refrigeration
- Fire equipment power monitoring system
- Smartphones
- Detection of phase loss
- Automotive permanent magnet synchronous motors
- Consumer electronics
- Microprocessor system
- Dash board
