CAT809LTBI-T3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-236-3, SC-59, SOT-23-3 |
| Number of Pins | 3 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 320mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.95mm |
| Base Part Number | CAT809 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 3 |
| Max Output Current | 20mA |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 8μA |
| Power Dissipation | 320mW |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 4.63V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.02mA |
| Min Reset Threshold Voltage | 4.56V |
| Max Reset Threshold Voltage | 4.7V |
| Threshold Voltage | +4.63V |
| Undervoltage Threshold | 4.56V |
| Overvoltage Threshold | 4.7V |
| Length | 2.92mm |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
CAT809LTBI-T3 Overview
This power management consists of 3 mounting terminals on which it can be mounted. It is packaged with Cut Tape (CT). Please find attached 1 functions for your reference in this IC power. It is possible to find on this power management a series of 1 channels. To assist you, this PMIC includes TO-236-3, SC-59, SOT-23-3 functions. Several of the benefits of this PMIC are also shared by other Simple Reset/Power-On Reset products. IC management conducts in a 5V-voltage supply. There is a voltage supply of 1 for the PMIC chip, and the chip conducts at that voltage. Surface Mount mounts IC management. In this case, this PMIC chip can be sub-categorized as a Power Management Circuits chip. The total number of pins on this power management is 3. There are 3 pins on the power managment ic. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 1.2V. The supply voltage (Vsup) should not exceed 5.5V volts in this IC power. Power management recommends the Surface Mount mounting type. This range of temperature should be set for the supervisors: -40°C~85°C TA. Power management has an output of Push-Pull, Totem Pole during operation. As far as the supply current of the power management is concerned, it is 20μA. It is always advisable to use CAT809, the base supervisor number, when searching for similar PMICs from the manufacturer. A power supply of 5V watts is required for the operation of this power management.
CAT809LTBI-T3 Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
20μA operating supply current
CAT809LTBI-T3 Applications
There are a lot of ON Semiconductor CAT809LTBI-T3 Voltage Supervisors applications.
- Battery-powered equipment
- Military communications
- Cloud computing
- Computer applications
- Analog circuit
- Kitchen appliances
- Set top box
- Rechargeable batteries
- Embedded computing
- Detection of phase loss
