CAT809SSDI-T3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-70, SOT-323 |
| Number of Pins | 3 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 175mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Base Part Number | CAT809 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 3 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 15μA |
| Nominal Supply Current | 15μA |
| Power Dissipation | 175mW |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 2.93V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 2.89V |
| Max Reset Threshold Voltage | 2.96V |
| Threshold Voltage | +2.93V |
| Undervoltage Threshold | 2.89V |
| Overvoltage Threshold | 2.96V |
| Length | 2mm |
| RoHS Status | RoHS Compliant |
CAT809SSDI-T3 Overview
This voltage supervisor has a total of 3 mounting terminals that can be used for mounting. Packaging is in the form of a Cut Tape (CT). As a reference, this IC management includes 1 functions for your convenience. This power managment ic consists of 1 channels, each of which can be used independently. The purpose of this IC power is to provide you with a reference of SC-70, SOT-323 functions. It is a IC power that shares many benefits with other products from the Simple Reset/Power-On Reset line. The supervisor is always powered by a 3.3V volt supply. In a 1 supply voltage, the PMIC chip conducts. Surface Mount mounts power management on the wall. There is a subcategory called Power Management Circuits for this power management. The total number of pins on this power management is 3. There are 3 pins on the power managment ic. Supply voltage (Vsup) should be at least 1.2V for this power management. The maximum supply voltage (Vsup) in this PMIC should not exceed 5.5V volts. Power management recommends the Surface Mount mounting type. The supervisors should be set to the following temperature: -40°C~85°C TA. During operation, this power management system outputs Push-Pull, Totem Pole. The supply current of the power management is 15μA. It is always advisable to use CAT809, the base supervisor number, when searching for similar PMICs from the manufacturer.
CAT809SSDI-T3 Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
15μA operating supply current
CAT809SSDI-T3 Applications
There are a lot of ON Semiconductor CAT809SSDI-T3 Voltage Supervisors applications.
- Electronics installed in the vehicle
- Multi-voltage system
- WiFi router
- Telecommunications equipment
- emergency room
- Military communications
- Fire equipment power monitoring system
- Detection of phase sequence
- Leakage protection
- Sensitive sensors
