CAT810LTBI-T3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-236-3, SC-59, SOT-23-3 |
| Number of Pins | 3 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 3 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 320mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.95mm |
| Base Part Number | CAT810 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 3 |
| Max Output Current | 20mA |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 8μA |
| Nominal Supply Current | 8μA |
| Power Dissipation | 320mW |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active High |
| Voltage - Threshold | 4.63V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.02mA |
| Min Reset Threshold Voltage | 4.56V |
| Max Reset Threshold Voltage | 4.7V |
| Threshold Voltage | +4.63V |
| Undervoltage Threshold | 4.56V |
| Overvoltage Threshold | 4.7V |
| Length | 2.92mm |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
CAT810LTBI-T3 Overview
A total of 3 terminals are used to mount this power management. Packaging is in the form of a Cut Tape (CT). The purpose of this IC management is to provide you with a reference of 1 functions. A series of 1 channels can be found on this supervisor. There are TO-236-3, SC-59, SOT-23-3 functions included in this PMIC so that you can refer to them. This IC power shares lots of benefits with other Simple Reset/Power-On Reset products. The supervisor is always powered by a 5V volt supply. When a supply voltage of 1 is applied to the power ic, it conducts. Power management is included in the Surface Mount mount. There is a subcategory of this power ic known as Power Management Circuits. A total of 3 pins are located on this power management. The pins of the power management system count 3. There should be a minimum voltage supply (Vsup) of 1.2V for this PMIC. This IC power should be powered by no more than 5.5V volts of supply voltage (Vsup). Power management' mounting is recommended to be done with the Surface Mount type of mounting. You should set the supervisor's temperature during -40°C~85°C TA . During operation, this power management system outputs Push-Pull, Totem Pole. In order to maintain a stable supply current for the power management, 8μA is the recommended value. You can always use CAT810, the base supervisor number, to search for similar PMICs of the manufacturer. A power supply of 5V watts is required for the operation of this power management.
CAT810LTBI-T3 Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
8μA operating supply current
CAT810LTBI-T3 Applications
There are a lot of ON Semiconductor CAT810LTBI-T3 Voltage Supervisors applications.
- Kitchen appliances
- DC stabilized power supply module
- Unattended substation automation
- Medical-specific insulation monitor
- Low voltage/high power - AI, GPU
- emergency room
- DVR
- Fire equipment power monitoring system
- Embedded computing
- Dash board
