CAT811MTBI-T3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-253-4, TO-253AA |
| Number of Pins | 4 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 4 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 320mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | CAT811 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 4 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 8μA |
| Power Dissipation | 320mW |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 4.38V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Supply Current-Max (Isup) | 0.02mA |
| Min Reset Threshold Voltage | 4.31V |
| Max Reset Threshold Voltage | 4.45V |
| Threshold Voltage | +4.38V |
| Undervoltage Threshold | 4.31V |
| Overvoltage Threshold | 4.45V |
| Length | 2.9mm |
| RoHS Status | RoHS Compliant |
CAT811MTBI-T3 Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 4 in total. In terms of packaging, power management follows the Tape & Reel (TR) model. Please refer to this PMIC for 1 functions. There are 1 channels on this power managment ic that can be found in a series. IC management is packaged as a TO-253-4, TO-253AA package. This IC power shares lots of benefits with other Simple Reset/Power-On Reset products. During operation, the power ic is supplied with a voltage of 5V. When a supply voltage of 1 is applied to the power ic, it conducts. By Surface Mount, IC management has been mounted. There is a subcategory of this power ic known as Power Management Circuits. It has a total of 4 pins that are attached to IC management. This power management has 4 pins. There should be a minimum voltage supply (Vsup) of 1.2V for this PMIC. The maximum supply voltage (Vsup) is not to exceed 5.5V volts in this IC management. Mounting type Surface Mount is recommended. The supervisors should be set to the following temperature: -40°C~85°C TA. During operation, this power management system outputs Push-Pull, Totem Pole. The supervisor's supply current is specified to 8μA. It is always advisable to use CAT811, the base supervisor number, when searching for similar PMICs from the manufacturer. It requires 5V watts of power to operate this voltage supervisor.
CAT811MTBI-T3 Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
8μA operating supply current
CAT811MTBI-T3 Applications
There are a lot of ON Semiconductor CAT811MTBI-T3 Voltage Supervisors applications.
- Analog circuit
- Radar
- Embedded computing
- Personal computers
- Medical-specific insulation monitor
- Radio
- Dash board
- Utility meter
- Refrigeration
- Satellite navigation
