CAT824UTDI-GT3
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-5 Thin, TSOT-23-5 |
| Number of Pins | 23 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 571mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.95mm |
| Output | Push-Pull, Totem Pole |
| Pin Count | 5 |
| JESD-30 Code | R-PDSO-G5 |
| Power Supplies | 2.5/3.3V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Power Dissipation | 571mW |
| Max Supply Current | 12μA |
| Adjustable Threshold | NO |
| Watchdog Timer | Yes |
| Reset | Active High/Active Low |
| Voltage - Threshold | 2V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 1.95V |
| Max Reset Threshold Voltage | 2.05V |
| Length | 2.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
CAT824UTDI-GT3 Overview
This voltage supervisor has a total of 5 mounting terminals that can be used for mounting. A Tape & Reel (TR) package is used to package the power management. To assist you, this IC power includes 1 functions. A series of 1 channels can be found on this supervisor. For your reference, this PMIC includes a list of SOT-23-5 Thin, TSOT-23-5 functions. There are a lot of similarities between this IC management and other Simple Reset/Power-On Reset products. IC management conducts at a voltage of 3.3V. When 1 is applied to the power ic, it conducts. Surface Mount mounts power management on the wall. Power Management Circuits is a subcategory of this PMIC chip. There are a total of 5 pins on power management. 23 pins make up the power management. In order for this IC power to function, the supply voltage (Vsup) cannot be less than 1.2V. The supply voltage (Vsup) should not exceed 5.5V volts in this IC power. Surface Mount is the recommended mounting type. The temperature of the supervisors should be set to this range: -40°C~85°C TA. When this power management system is in operation, it produces an output voltage of Push-Pull, Totem Pole. In order to operate this power management, it requires 2.5/3.3V volts of power. A maximum supply temperature of 12μA can be used with this power management.
CAT824UTDI-GT3 Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
CAT824UTDI-GT3 Applications
There are a lot of ON Semiconductor CAT824UTDI-GT3 Voltage Supervisors applications.
- Battery cars
- Medical-specific insulation monitor
- Electrical fire monitoring system
- Unattended substation automation
- Leakage protection
- Power distribution systems of ICU
- Consumer electronics
- FPGA design
- Smart meter
- Battery cars
