CBT3245APW-Q100J
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Series | 74CBT |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | Bus Switch |
| Resistance | 10Ohm |
| Technology | CMOS |
| Voltage - Supply | 4V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74CBT3245 |
| Pin Count | 20 |
| Operating Supply Voltage | 5V |
| Circuit | 8 x 1:1 |
| Supply Voltage-Min (Vsup) | 4V |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Propagation Delay | 6 ns |
| Quiescent Current | 3μA |
| Family | CBT/FST/QS/5C/B |
| Output Characteristics | 3-STATE |
| Supply Type | Single |
| Output Polarity | TRUE |
| High Level Output Current | -128mA |
| Low Level Output Current | 128mA |
| Voltage Supply Source | Single Supply |
| Independent Circuits | 1 |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
CBT3245APW-Q100J Overview
In order to save board space, digital switch is located in the 20-TSSOP (0.173, 4.40mm Width).As a result, it is packaged in the way of Tape & Reel (TR).Mounting is performed using Surface Mount.The multiplexers uses an analog IC Bus Switch as the analog part of the circuit.The operating temperature of -40°C~85°C will not be susceptible to external factors.It provides digital controlled switch's superior flexibility for designers to use when it operates with a supply voltage of 4V~5.5V.provides digital controlled switch's digital controlled switch'sSeveral applications are possible for 74CBT series multiplexers.The basic configuration includes 20 terminations.To find signal switch's related components, a base part number of 74CBT3245 may also be used.The multiplexer's system is supplied with a voltage of 5V.A component pin count of 20 is found on this turn signal switch.Using the point GULL WING as an end point of conductors, it is used to determine the terminus of a conductor.There is a type of supply of Single.Currently, it is configured with 20 pins.This unit is mounted in the way of Surface Mount.I would like to refer to the logic switch as a member of the CBT/FST/QS/5C/B family.There are 8 bits signal multiplexer provides.To prevent unnecessary failures, it is recommended that the minimum supply voltage (Vsup) remain at 4V.It consumes 3μA current of multiplexer ic without external influences.If the supply voltage is 5V, reliable performance of the multiplexers can be achieved.The signal switching operates with a resistance of 2.This signal switching operates at a resistance of 10Ohm.
CBT3245APW-Q100J Features
Supplied in the 20-TSSOP (0.173, 4.40mm Width) package
Adopting a supply type of Single
Operating with the supply voltage of 5V
CBT3245APW-Q100J Applications
There are a lot of Nexperia USA Inc. CBT3245APW-Q100J Signal Switches / Multiplexers / Decoders applications.
- Time division multiplexing system
- Speed control of medern motors
- Code converters
- A robotic vehicle with the metal detector
- Image transmission
- Data distribution
- Enabling different functions units in microprocessor instruction decoding
- Metal detectors
- Home automation system
- Communication system
