CD4051BCN
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Supplier Device Package | 16-PDIP |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2002 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Termination | Through Hole |
| Resistance | 1.05kOhm |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Max Power Dissipation | 700mW |
| Base Part Number | 4051 |
| Number of Outputs | 1 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 5V |
| Nominal Supply Current | 20μA |
| Power Dissipation | 700mW |
| Propagation Delay | 55 ns |
| Turn On Delay Time | 1.2 μs |
| Logic Function | Demultiplexer, Multiplexer |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 5V~15V ±2.5V~7.5V |
| Supply Type | Dual, Single |
| Bandwidth | 40MHz |
| Turn-Off Delay Time | 420 ns |
| Max Dual Supply Voltage | 7.5V |
| Number of Gates | 1 |
| -3db Bandwidth | 40MHz |
| On-State Resistance (Max) | 240Ohm |
| Min Dual Supply Voltage | 2.5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Current - Leakage (IS(off)) (Max) | 50nA |
| Switch Time (Ton, Toff) (Max) | 320ns, 150ns |
| Channel-to-Channel Matching (ΔRon) | 5Ohm |
| Crosstalk | -40dB @ 3MHz |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
CD4051BCN Overview
Due to its 16-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. In order to provide high reliability, an advanced packaging method Tube is used. In Through Hole, you'll find this switch device. Multiplexers and demultiplexers have the same number of circuits 8:1. Extended operating temperature around -55°C~125°C TA. A high-quality output is provided by the electrical component's 1 channels. Circuits number 1 make up this analogue multiplexer. Search with 4051 if you are looking for analog multiplexer variants. An switch multiplexer with 1.05kOhm internal resistance has a value of 1.05kOhm. For details about the functions of 16 pins, please refer to the datasheets. In normalcircumstances, users should not exceed 15V volts for the multiplexer. The analog switch ic is of the Dual, Single supply type and is cost-effective. It is recommended to use 5V as the lowest voltage for the electrical part. For this switch, a dual supply voltage is feasible, but it must not exceed 7.5VWith dual power supplies, you should attach at least 2.5V. The electrical component supports 8 inputs. 40MHz-bandwidths can be used to transfer data between multiplexers. The switches should not operate in an environment where the temperature is higher than 125°C. There are 1 outputs on the analogue multiplexer. Suppliers offer the 16-PDIP package.
CD4051BCN Features
1 Channels
-3db Bandwidth: 40MHz
Bandwidth: 40MHz
CD4051BCN Applications
There are a lot of ON Semiconductor CD4051BCN Analog Switches & Multiplexers ICs applications.
- Microprocessor Controlled Analog Systems
- PBX interfaces
- USB 1.1 signal switching circuits
- Optical Applications
- Residential Gateways, Home Gateway/Router
- Communications systems
- Fault Tolerant Systems
- MP3 players
- High reliability control systems
- Modems
