Parameters |
Packaging |
Cut Tape (CT) |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
240Ohm |
Terminal Finish |
Matte Tin (Sn) |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
5V |
Base Part Number |
CD4052 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
18V |
Polarity |
Non-Inverting |
Number of Channels |
4 |
Number of Circuits |
2 |
Max Supply Voltage |
20V |
Min Supply Voltage |
3V |
Operating Supply Current |
80nA |
Nominal Supply Current |
100μA |
Number of Bits |
4 |
Propagation Delay |
60 ns |
Quiescent Current |
80nA |
Turn On Delay Time |
720 ns |
Logic Function |
Multiplexer |
Number of Inputs |
8 |
Voltage - Supply, Single/Dual (±) |
3V~20V ±2.5V~9V |
Supply Type |
Dual, Single |
Bandwidth |
25MHz |
Supply Current-Max (Isup) |
3mA |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
450 ns |
Max Dual Supply Voltage |
9V |
On-State Resistance (Max) |
240Ohm |
Min Dual Supply Voltage |
2.5V |
Dual Supply Voltage |
5V |
Multiplexer/Demultiplexer Circuit |
4:1 |
Off-state Isolation-Nom |
40 dB |
Current - Leakage (IS(off)) (Max) |
100nA |
Channel Capacitance (CS(off), CD(off)) |
0.2pF 18pF |
On-state Resistance Match-Nom |
15Ohm |
Switch Circuit |
SP4T |
Channel-to-Channel Matching (ΔRon) |
5 Ω |
Crosstalk |
-40dB @ 10MHz |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
125Ohm |
Normal Position |
NC |
Signal Current-Max |
0.01A |
Height |
1.2mm |
Length |
5mm |
Width |
4.4mm |
Thickness |
1mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 2 days ago) |
Contact Plating |
Gold |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
16 |
Weight |
61.887009mg |
Operating Temperature |
-55°C~125°C TA |
CD4052BPWR Overview
The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). In order to provide high reliability, an advanced packaging method Cut Tape (CT) is used. Mounted in Surface Mount is this multiplexer. There is 4:1 ratio between the number of multiplexers and demultiplexers. Operating temperature extended to -55°C~125°C TA. In total, 16 terminations have occurred. This electronic part offers high-quality output due to its 4 channels. A 5V voltage supply should turn on and run the electronic component. Into the electrical component body are injected 16 pins. On the other hand, analog switches can be constructed using SP4T switching circuits. It consists of 2 circuits. Try searching with CD4052 to find analog multiplexer variants. It has an internal resistance of 240Ohm. For functions related to 16 pins, please refer to the datasheets. Users shouldn't supply more than 20V voltage to the switch device. The digital multiplexer has a low cost Dual, Single supply. 3V is the lowest voltage the electrical component should receive. An operating current of 80nA would be sufficient for this switch device. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 9V. It is recommended that you attach at least 2.5V to your dual power supply. There are SEPARATE OUTPUT outputs on this analog switch ic. 18V operating voltages can be used with this electrical part. In order to operate the 8 inputs, there are several steps to follow. There are 25MHz bandwidths for data transfer. A Drain to Source resistance of 125Ohm is shown for this electronic part. It is able to conduct in a 4-bit way.
CD4052BPWR Features
4 Channels
Switch Circuit: SP4T
80nA Supply Current
Bandwidth: 25MHz
Drain-to-Source resistance: 125Ohm
4-Bit
CD4052BPWR Applications
There are a lot of Texas Instruments CD4052BPWR Analog Switches & Multiplexers ICs applications.
- DSUs
- High-Voltage
- HDTV
- FTTH
- Fiber to the Home
- SONET
- Multi-Line E1 Interface Cards
- New designs requiring multiplexer functions
- Precision test equipment
- Remote wireless modules