CD4097BPWRE4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 24 |
| Weight | 89.499445mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| Resistance | 240Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | CD4097 |
| Pin Count | 24 |
| Qualification Status | Not Qualified |
| Power Supplies | 5/15V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 3V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Operating Supply Current | 80nA |
| Nominal Supply Current | 100μA |
| Power Dissipation | 500mW |
| Number of Bits | 8 |
| Propagation Delay | 60 ns |
| Turn On Delay Time | 650 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Number of Inputs | 16 |
| Supply Type | Single |
| Bandwidth | 20MHz |
| Supply Current-Max (Isup) | 0.6mA |
| Turn-Off Delay Time | 440 ns |
| On-State Resistance (Max) | 240Ohm |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 0.2pF 35pF |
| On-state Resistance Match-Nom | 15Ohm |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 3V~18V |
| Height | 1.2mm |
| Length | 7.8mm |
| Width | 4.4mm |
| Thickness | 1mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD4097BPWRE4 Overview
The electrical component comes in 24-TSSOP (0.173, 4.40mm Width) packaging, which makes it convenient to ship overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. 8:1 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around -55°C~125°C TA. In total, there are 24 terminations. A high-quality output is provided by the electrical component's 2 channels. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. This electronic part can be found in the 24 series. A total of 2 circuits make up this switch device. Use CD4097 to search for variants of the digital switches. As far as internal resistance is concerned, it has 240Ohm. Please refer to the datasheets for 24 pins functions. It is a typical Multiplexer or Switches analog multiplexer. In a normalsituation, users should not supply the switches with voltage higher than 18V. An effective Single supply digital multiplexer. It is recommended that the electrical component receives a voltage of 3V. An operating current of 80nA would be sufficient for this switch device. A voltage of 3V~18V is required to drain this analog switch from a single voltage supply. A DIFFERENTIAL MULTIPLEXER analog IC is integrated into the board. Operating 16 inputs is required. In 20MHz-bandwidths, data can be transferred. 8-bit conductivity is possible.
CD4097BPWRE4 Features
2 Channels
80nA Supply Current
Bandwidth: 20MHz
8-Bit
CD4097BPWRE4 Applications
There are a lot of Texas Instruments CD4097BPWRE4 Analog Switches & Multiplexers ICs applications.
- Cell phones
- Audio and video signal routing
- Precision data acquisition
- Medical Instrumentation
- Cable PC
- Fault Tolerant Systems
- Channelized and Unchannelized DS3 applications
- Battery-powered systems
- SDH
- Audio and video routing
