CD74AC574MG4
| Parameters | |
|---|---|
| Packaging | Tube |
| Series | 74AC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Additional Feature | BROADSIDE VERSION OF 374 |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 1.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Base Part Number | 74AC574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 3.3/5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 125MHz |
| Propagation Delay | 135 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 2.7 ns |
| Family | AC |
| Logic Function | D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 10.8ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -55°C~125°C TA |
CD74AC574MG4 Overview
In the form of 20-SOIC (0.295, 7.50mm Width), it has been packaged. A package named Tubeincludes it. The output it is configured with uses Tri-State, Non-Inverted. Positive Edgeis the trigger it is configured with. Surface Mountis in the way of this electric part. The JK flip flop operates with an input voltage of 1.5V~5.5V volts. It is operating at -55°C~125°C TA. Logic flip flops of this type are classified as D-Type. In FPGA terms, D flip flop is a type of 74ACseries FPGA. In order for it to function properly, its output frequency should not exceed 125MHz. There are 1 elements in it. 20terminations have occurred. The 74AC574 family contains it. A voltage of 3.3V provides power to the D latch. A 10pFfarad input capacitance is provided by this T flip flop. A device of this type belongs to the family of AC. Electronic part Surface Mountis mounted in the way. A total of 20pins are provided on this board. A Positive Edgeclock edge trigger is used in this device. It is part of the FF/Latchesbase part number family. There are 8bits in its design. Vsup reaches its maximum value at 5.5V. The superior flexibility is achieved through the use of 8 circuits. The system runs on a power supply of 3.3/5V watts. This flip flop has a total of 2ports. In addition to its maximum design flexibility, the output current of the T flip flop is 24mA. It consumes 8μA current. Additionally, you may refer to the D latch's additional BROADSIDE VERSION OF 374.
CD74AC574MG4 Features
Tube package
74AC series
20 pins
8 Bits
3.3/5V power supplies
CD74AC574MG4 Applications
There are a lot of Texas Instruments CD74AC574MG4 Flip Flops applications.
- Parallel data storage
- Instrumentation
- Single Down Count-Control Line
- Count Modes
- CMOS Process
- Counters
- Test & Measurement
- Bus hold
- Communications
- Storage Registers
