CD74ACT112MG4
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 16 |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Frequency | 100MHz |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Current - Output | 24mA |
| Number of Bits | 2 |
| Propagation Delay | 10.3 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 2.6 ns |
| Family | ACT |
| Logic Function | AND, JK-Type |
| Logic IC Type | J-K FLIP-FLOP |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Schmitt Trigger | No |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Negative Edge |
| Height | 1.75mm |
| Length | 9.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
CD74ACT112MG4 Overview
The flip flop is packaged in SOIC. A total of 2elements are contained within it. 16terminations have occurred. Power is supplied from a voltage of 5V volts. Electronic devices of this type belong to the ACTfamily. This electronic part is mounted in the way of Surface Mount. 16pins are included in its design. There is a clock edge trigger type of Negative Edgeon this device. There is a FF/Latchesbase part number assigned to the RS flip flops. The flip flop is designed with 2bits. Due to its reliability, this T flip flop is well suited for TUBE. An electrical current of 5V volts is applied to it. Optimal efficiency requires a supply voltage of 5V. There are 1 output Lines, which generate the binary equivalent of the input line whose value is equal to “1” and are available to encode either a decimal or hexadecimal input pattern to typically a binary or “B. C. D” (binary coded decimal) output code. Quiescent current is consumed by the D latch in the amount of 4μA. A -24mAis set for the high level output current. It is set to 24mAfor the low level output current. Operating temperatures should be lower than 125°C. It is recommended that the operating temperature be greater than -55°C. It operates with the minimal supply voltage of 4.5V. 5.5Vis the maximum supply voltage it supports. It is possible to achieve 100MHz frequencies. The logic IC it uses is J-K FLIP-FLOP. There are 2 functions available on the JK flip flop. There are 16 pins on the D latch. It offers maximum design flexibility with its output current of 24mA.
CD74ACT112MG4 Features
16 pins
2 Bits
5V power supplies
2 Functions
16 pin count
CD74ACT112MG4 Applications
There are a lot of Texas Instruments CD74ACT112MG4 Flip Flops applications.
- Counters
- Buffered Clock
- Memory
- Dynamic threshold performance
- ESD performance
- Data storage
- Divide a clock signal by 2 or 4
- Data Synchronizers
- Reduced system switching noise
- Convert a momentary switch to a toggle switch
