CD74ACT174M
| Parameters | |
|---|---|
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latch |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74ACT174 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 7 |
| Load Capacitance | 50pF |
| Output Current | 24mA |
| Number of Bits | 6 |
| Clock Frequency | 80MHz |
| Propagation Delay | 14 ns |
| Turn On Delay Time | 3.5 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 14ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Power Supply Current-Max (ICC) | 0.08mA |
| Number of Output Lines | 6 |
| fmax-Min | 80 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 80000000Hz |
| Height | 1.75mm |
| Length | 9.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | D-Type |
CD74ACT174M Overview
As a result, it is packaged as 16-SOIC (0.154, 3.90mm Width). A package named Tubeincludes it. T flip flop uses Non-Invertedas its output configuration. The trigger it is configured with uses Positive Edge. There is an electronic component mounted in the way of Surface Mount. The supply voltage is set to 4.5V~5.5V. It is operating at a temperature of -55°C~125°C TA. It is an electronic flip flop with the type D-Type. In terms of FPGAs, it belongs to the 74ACT series. There should be no greater frequency than 80MHzon its output. The list contains 1 elements. As a result, it consumes 8μA of quiescent current without being affected by external factors. 16terminations have occurred. The 74ACT174 family contains it. A voltage of 5V provides power to the D latch. A JK flip flop with a 10pFfarad input capacitance is used here. A device of this type belongs to the family of ACT. The electronic part is mounted in the way of Surface Mount. The 16pins are designed into the board. This device's clock edge trigger type is Positive Edge. The part is included in FF/Latch. The flip flop is designed with 6bits. Despite its superior flexibility, it relies on 7 circuits to achieve it. In order for the device to operate, it requires 5V power supplies. For high efficiency, the supply voltage should be set to 5V. With an output current of 24mA, it is possible to design the device in any way you want. There are 6 output lines on it.
CD74ACT174M Features
Tube package
74ACT series
16 pins
6 Bits
5V power supplies
CD74ACT174M Applications
There are a lot of Texas Instruments CD74ACT174M Flip Flops applications.
- Bounce elimination switch
- Dynamic threshold performance
- Patented noise
- Computers
- Automotive
- Frequency Dividers
- Balanced Propagation Delays
- Bus hold
- Load Control
- Buffer registers
