CD74ACT273PW
| Parameters | |
|---|---|
| Weight | 76.997305mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74ACT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 85MHz |
| Propagation Delay | 13.5 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 3.4 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 24mA 24mA |
| Max Propagation Delay @ V, Max CL | 12.3ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
CD74ACT273PW Overview
The flip flop is packaged in 20-TSSOP (0.173, 4.40mm Width). D flip flop is embedded in the Tube package. Currently, the output is configured to use Non-Inverted. The trigger configured with it uses Positive Edge. It is mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 4.5V~5.5V. It is operating at -55°C~125°C TA. The type of this D latch is D-Type. The FPGA belongs to the 74ACT series. You should not exceed 85MHzin its output frequency. In total, there are 1 elements. It has been determined that there have been 20 terminations. The object belongs to the 74ACT273 family. It is powered from a supply voltage of 5V. The input capacitance of this JK flip flopis 10pF farads. Devices in the ACTfamily are electronic devices. There is an electronic part that is mounted in the way of Surface Mount. As you can see from the design, it has pins with 20. This device exhibits a clock edge trigger type of Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. This flip flop is designed with 8 Bits. The superior flexibility of this product is achieved by using 8 circuits. An electrical current of 5V volts is applied to it. Optimal efficiency requires a supply voltage of 5V. Its output current of 24mAallows for maximum design flexibility. There are no output lines on the JK flip flop. There is 8μA quiescent current consumption by it.
CD74ACT273PW Features
Tube package
74ACT series
20 pins
8 Bits
5V power supplies
CD74ACT273PW Applications
There are a lot of Texas Instruments CD74ACT273PW Flip Flops applications.
- Data transfer
- Memory
- Asynchronous counter
- Storage Registers
- Control circuits
- Single Down Count-Control Line
- Power down protection
- Storage registers
- Convert a momentary switch to a toggle switch
- Functionally equivalent to the MC10/100EL29
