CD74ACT273PWRE4
| Parameters | |
|---|---|
| Contact Plating | Gold |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Frequency | 85MHz |
| Pin Count | 20 |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Current - Output | 24mA |
| Propagation Delay | 13.5 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 3.4 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| Number of Bits per Element | 8 |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Number of Output Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
CD74ACT273PWRE4 Overview
TSSOPis the way it is packaged. D flip flop is included in the Tape & Reel (TR)package. D latch consists of 1 elements. A total of 20 terminations have been made. It is powered by a voltage of 5V . A device of this type belongs to the family of ACT. Surface Mount mounts this electronic component. This board has 20 pins. This device exhibits a clock edge trigger type of Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. On the basis of its reliable performance, this D flip flop is well suited for use with TAPE AND REEL. It operates from 5V power supplies. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. It has 4 output lines to operate. It consumes a total of 8μA quiescent current at any given time. There is -24mA output current at the high level. In the low level output current setting, 24mAis used. It is recommended that the operating temperature be below 125°C. If the operating temperature is higher than -55°C, the system should operate properly. The RS flip flop is designed to operate with a minimal supply voltage of 4.5VV. It supports a maximum supply voltage of 5.5V volts. The frequency that can be achieved is 85MHz. This logic IC is D FLIP-FLOP. The T flip flop is equipped with 1functions . It has 20 pins. The output current of 24mA makes it feature maximum design flexibility.
CD74ACT273PWRE4 Features
Tape & Reel (TR) package
20 pins
5V power supplies
1 Functions
20 pin count
CD74ACT273PWRE4 Applications
There are a lot of Texas Instruments CD74ACT273PWRE4 Flip Flops applications.
- Data storage
- Single Up Count-Control Line
- High Performance Logic for test systems
- Frequency Divider circuits
- Event Detectors
- Digital electronics systems
- Computing
- Single Down Count-Control Line
- Parallel data storage
- Balanced 24 mA output drivers
