CD74ACT273PWRG4
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Frequency | 85MHz |
| Pin Count | 20 |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Current - Output | 24mA |
| Propagation Delay | 13.5 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 3.4 ns |
| Family | ACT |
| Logic Function | D-Type |
| Logic IC Type | D FLIP-FLOP |
| Max I(ol) | 0.024 A |
| Number of Bits per Element | 8 |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
CD74ACT273PWRG4 Overview
In the form of TSSOP, it has been packaged. The Tape & Reel (TR)package contains it. In total, it contains 1 elements. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The D flip flop is powered by a voltage of 5V . The electronic device belongs to the ACTfamily. This electronic part is mounted in the way of Surface Mount. The electronic flip flop is designed with pins 20. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. As a result of its reliability, this D flip flop is ideally suited for TR. It runs on 5Vvolts of power. If high efficiency is desired, the supply voltage should be kept at 5V. Despite external influences, it consumes 8μAof quiescent current. -24mAis the output current at high level. 24mAis set as the low level output current. It is recommended that the operating temperature be lower than 125°C. The operating temperature should be higher than -55°C. It is powered by 4.5V as its minimum supply voltage. It is capable of supporting a maximum supply voltage of 5.5V. It is possible to achieve a frequency of 85MHz. D FLIP-FLOPis used as the logic IC in this D flip flop. A total of 1 functions are available on the T flip flop. There are 20 pins on the D latch. 24mA provides maximum design flexibility due to its output current.
CD74ACT273PWRG4 Features
Tape & Reel (TR) package
20 pins
5V power supplies
1 Functions
20 pin count
CD74ACT273PWRG4 Applications
There are a lot of Texas Instruments CD74ACT273PWRG4 Flip Flops applications.
- Data transfer
- Test & Measurement
- Bounce elimination switch
- Frequency Divider circuits
- Cold spare funcion
- Asynchronous counter
- Communications
- Shift Registers
- Single Up Count-Control Line
- Differential Individual
