CD74ACT574E
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Gold |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Weight | 1.1991g |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | Bus Driver/Transceiver |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | 74ACT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 110MHz |
| Propagation Delay | 11.2 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 2.8 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 11.2ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height | 5.08mm |
| Length | 24.33mm |
| Width | 6.35mm |
| Thickness | 4.57mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74ACT574E Overview
In the form of 20-DIP (0.300, 7.62mm), it has been packaged. Package Tubeembeds it. T flip flop uses Tri-State, Non-Invertedas its output configuration. The trigger it is configured with uses Positive Edge. It is mounted in the way of Through Hole. A 4.5V~5.5Vsupply voltage is required for it to operate. It is at -55°C~125°C TAdegrees Celsius that the system is operating. It belongs to the type D-Typeof flip flops. The FPGA belongs to the 74ACT series. This D flip flop should not have a frequency greater than 110MHz. A total of 1elements are present in it. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. This D latch belongs to the family of 74ACT574. Power is provided by a 5V supply. JK flip flop input capacitance is 10pF farads. It is a member of the ACTfamily of D flip flop. There is an electronic component mounted in the way of Through Hole. The 20pins are designed into the board. The clock edge trigger type for this device is Positive Edge. There is a Bus Driver/Transceiverbase part number assigned to the RS flip flops. This flip flop is designed with 8 Bits. The superior flexibility of this circuit is achieved by using 8 circuits. It runs on 5Vvolts of power. A total of 2ports are embedded in the D flip flop. In order to ensure high efficiency, the supply voltage should remain at 5V. It offers maximum design flexibility with its output current of 24mA. In order to operate, the chip has 3 output lines. It consumes a total of 8μA quiescent current at any given time.
CD74ACT574E Features
Tube package
74ACT series
20 pins
8 Bits
5V power supplies
CD74ACT574E Applications
There are a lot of Texas Instruments CD74ACT574E Flip Flops applications.
- Pattern generators
- Computing
- EMI reduction circuitry
- Reduced system switching noise
- Cold spare funcion
- Balanced 24 mA output drivers
- Count Modes
- Patented noise
- Latch
- Power down protection
