CD74ACT574ME4
| Parameters | |
|---|---|
| Contact Plating | Gold |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Packaging | Rail/Tube |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 110MHz |
| Pin Count | 20 |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 24mA |
| Propagation Delay | 165 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 2.8 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.024 A |
| Number of Bits per Element | 8 |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
CD74ACT574ME4 Overview
SOICis the way it is packaged. There is an embedded version in the package Rail/Tube. D latch consists of 1 elements. 20terminations have occurred. A voltage of 5V is used to power it. This D flip flop belongs to the family of ACT. The electronic part is mounted in the way of Surface Mount. This board is designed with 20pins on it. This device exhibits a clock edge trigger type of Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. In order for the device to operate, it requires 5V power supplies. This flip flop has a total of 2ports. The supply voltage should be maintained at 5V for high efficiency. In order for the chip to function, it has 3output lines. As a result, it consumes 8μA of quiescent current without being affected by external factors. A high level output current of -24mAis set. In the low level output current setting, 24mAis used. Ideally, the operating temperature should be lower than 125°C. In order for the system to operate properly, the temperature should be higher than -55°C. The minimum voltage required for operation is 4.5V. In this case, it supports a maximum supply voltage of 5.5V. It is possible to obtain a frequency of 110MHz. There is a logic IC BUS DRIVER used in the D flip flop. There are 1 functions available on this T flip flop. The D latch is equipped with 20 pins. As a result of the output current of 24mA, the design flexibility is maximized.
CD74ACT574ME4 Features
Rail/Tube package
20 pins
5V power supplies
1 Functions
20 pin count
CD74ACT574ME4 Applications
There are a lot of Texas Instruments CD74ACT574ME4 Flip Flops applications.
- Safety Clamp
- Reduced system switching noise
- Divide a clock signal by 2 or 4
- Frequency Divider circuits
- EMI reduction circuitry
- Convert a momentary switch to a toggle switch
- Shift registers
- Supports Live Insertion
- Event Detectors
- Patented noise
