CD74ACT74M96E4
| Parameters | |
|---|---|
| Contact Plating | Gold |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Frequency | 85MHz |
| Pin Count | 14 |
| Number of Outputs | 4 |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Current - Output | 24mA |
| Number of Bits | 1 |
| Propagation Delay | 12.5 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 2.4 ns |
| Family | ACT |
| Logic Function | AND, D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Number of Input Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 8.65mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
CD74ACT74M96E4 Overview
SOICis the packaging method. As part of the package Tape & Reel (TR), it is embedded. The list contains 2 elements. It has been determined that there have been 14 terminations. Power is provided by a 5V supply. In terms of electronic devices, this device belongs to the ACTfamily of devices. There is an electronic part mounted in the way of Surface Mount. 14pins are included in its design. This device's clock edge trigger type is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. Flip flops designed with 1bits are used in this part. Due to its reliability, this T flip flop is well suited for TAPE AND REEL. The D latch runs on a voltage of 5V volts. The supply voltage should be maintained at 5V for high efficiency. Currently, there are 1 lines of input. It consumes 4μA current. In this case, the high level output current is set to -24mA. 24mA is the low level output current. The operating temperature should be lower than 125°C. Ideally, the operating temperature should be greater than -55°C. The RS flip flop is designed to operate with a minimal supply voltage of 4.5VV. It supports the maximal supply voltage of 5.5V. This can be achieved at a frequency of 85MHz. In this case, it uses a D FLIP-FLOP logic IC. It is equipped with 2 functions . With 14 pins, it is equipped with a low power consumption. It features maximum design flexibility due to the 24mA output current.
CD74ACT74M96E4 Features
Tape & Reel (TR) package
14 pins
1 Bits
5V power supplies
2 Functions
14 pin count
CD74ACT74M96E4 Applications
There are a lot of Texas Instruments CD74ACT74M96E4 Flip Flops applications.
- Buffer registers
- Bus hold
- Buffered Clock
- Individual Asynchronous Resets
- Frequency Dividers
- Instrumentation
- Circuit Design
- Load Control
- Divide a clock signal by 2 or 4
- Registers
