CD74FCT374M96
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74FCT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | BICMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Base Part Number | 74FCT374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 48mA |
| Number of Bits | 8 |
| Clock Frequency | 70MHz |
| Propagation Delay | 6.6 ns |
| Turn On Delay Time | 6.6 ns |
| Family | FCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 15mA 48mA |
| Max Propagation Delay @ V, Max CL | 6.6ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74FCT374M96 Overview
The package is in the form of 20-SOIC (0.295, 7.50mm Width). As part of the package Tape & Reel (TR), it is embedded. This output is configured with Tri-State, Non-Inverted. This trigger is configured to use Positive Edge. There is an electric part mounted in the way of Surface Mount. With a supply voltage of 4.75V~5.25V volts, it operates. A temperature of 0°C~70°C TAis used in the operation. D-Typeis the type of this D latch. JK flip flop belongs to the 74FCTseries of FPGAs. In order for it to function properly, its output frequency should not exceed 70MHz. The list contains 1 elements. T flip flop consumes 8μA quiescent energy. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. The 74FCT374 family contains this object. Power is provided by a 5V supply. The input capacitance of this T flip flop is 10pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. Electronic devices of this type belong to the FCTfamily. In this case, the electronic component is mounted in the way of Surface Mount. This board is designed with 20pins on it. This device's clock edge trigger type is Positive Edge. This device has the base part number FF/Latches. It is designed with a number of bits of 8. To achieve this superior flexibility, 8 circuits are used. As a result of its reliability, this D flip flop is ideally suited for TAPE AND REEL. The D latch runs on a voltage of 5V volts. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. For high efficiency, the supply voltage should be set to 5V. In addition to its maximum design flexibility, the output current of the T flip flop is 48mA. It has 3 output lines to operate.
CD74FCT374M96 Features
Tape & Reel (TR) package
74FCT series
20 pins
8 Bits
5V power supplies
CD74FCT374M96 Applications
There are a lot of Texas Instruments CD74FCT374M96 Flip Flops applications.
- Differential Individual
- Power down protection
- Load Control
- High Performance Logic for test systems
- Digital electronics systems
- Storage registers
- Shift registers
- Control circuits
- Latch
- Count Modes
