CD74HC109M96E4
| Parameters | |
|---|---|
| Contact Plating | Gold |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | FF/Latch |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 4.5V |
| Frequency | 60MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Load Capacitance | 50pF |
| Current - Output | 5.2mA |
| Number of Bits | 2 |
| Propagation Delay | 175 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 14 ns |
| Family | HC/UH |
| Logic Function | AND, Flip-Flop, JK-Type |
| Logic IC Type | J-KBAR FLIP-FLOP |
| Max I(ol) | 0.004 A |
| High Level Output Current | -5.2mA |
| Low Level Output Current | 5.2mA |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
CD74HC109M96E4 Overview
SOICis the way it is packaged. Package Tape & Reel (TR)embeds it. There are 2 elements in it. It has been determined that there have been 16 terminations. Power is supplied from a voltage of 4.5V volts. The electronic device belongs to the HC/UHfamily. A part of the electronic system is mounted in the way of Surface Mount. The 16pins are designed into the board. There is a clock edge trigger type of Positive Edgeon this device. This RS flip flops is a part number FF/Latch. Flip flops designed with 2bits are used in this part. In light of its reliable performance, this T flip flop is well suited for TAPE AND REEL. The JK flip flop is with 1 output lines to operate. In terms of quiescent current, it consumes 4μA . The high level output current is set to -5.2mA. It is set to 5.2mAfor low level output current. Ideally, the operating temperature should be lower than 125°C. A temperature above -55°Cshould be used for the operation. A minimum supply voltage of 2V is required for these RS flip flops to operate. The maximum supply voltage supported by the flip flop is 6V. It is possible to achieve 60MHz frequencies. It uses J-KBAR FLIP-FLOPas its logic IC. It is equipped with 2 functions . A total of 16 pins are present on this device. The 5.2mA output current allows it to be designed with the greatest amount of flexibility.
CD74HC109M96E4 Features
Tape & Reel (TR) package
16 pins
2 Bits
2 Functions
16 pin count
CD74HC109M96E4 Applications
There are a lot of Texas Instruments CD74HC109M96E4 Flip Flops applications.
- ESD performance
- Pattern generators
- Storage Registers
- Shift registers
- Power down protection
- Communications
- Buffered Clock
- Control circuits
- Individual Asynchronous Resets
- Counters
