CD74HC173MT
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | SMD/SMT |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | WITH DUAL OUTPUT ENABLE |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 4.5V |
| Base Part Number | 74HC173 |
| Function | Master Reset |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 4 |
| Load Capacitance | 50pF |
| Output Current | 7.8mA |
| Number of Bits | 4 |
| Clock Frequency | 60MHz |
| Propagation Delay | 200 ns |
| Turn On Delay Time | 17 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 34ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Input Lines | 2 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 9.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
CD74HC173MT Overview
16-SOIC (0.154, 3.90mm Width)is the packaging method. It is contained within the Tape & Reel (TR)package. This output is configured with Tri-State, Non-Inverted. It is configured with the trigger Positive Edge. This electronic part is mounted in the way of Surface Mount. Powered by a 2V~6Vvolt supply, it operates as follows. A temperature of -55°C~125°C TAis used in the operation. It is an electronic flip flop with the type D-Type. JK flip flop is a part of the 74HCseries of FPGAs. You should not exceed 60MHzin its output frequency. In total, there are 1 elements. As a result, it consumes 8μA of quiescent current without being affected by external factors. A total of 16terminations have been recorded. The object belongs to the 74HC173 family. It is powered by a voltage of 4.5V . This JK flip flop has a 10pFfarad input capacitance. Electronic devices of this type belong to the HC/UHfamily. It is mounted by the way of Surface Mount. A total of 16pins are provided on this board. The clock edge trigger type for this device is Positive Edge. The part is included in FF/Latches. 4bits are used in its design. Vsup reaches 6V, the maximal supply voltage. For normal operation, the supply voltage (Vsup) should be above 2V. The superior flexibility is achieved through the use of 4 circuits. In view of its reliability, this D flip flop is a good fit for TAPE AND REEL. With a current output of 7.8mA , it offers maximum design flexibility. There are 3 output Lines, which generate the binary equivalent of the input line whose value is equal to “1” and are available to encode either a decimal or hexadecimal input pattern to typically a binary or “B. C. D” (binary coded decimal) output code. A total of 2input lines have been provided. Additionally, there are WITH DUAL OUTPUT ENABLE on the electronic flip flop that can be referred to.
CD74HC173MT Features
Tape & Reel (TR) package
74HC series
16 pins
4 Bits
CD74HC173MT Applications
There are a lot of Texas Instruments CD74HC173MT Flip Flops applications.
- Shift registers
- Storage registers
- Counters
- Divide a clock signal by 2 or 4
- Load Control
- Matched Rise and Fall
- Common Clocks
- Differential Individual
- Instrumentation
- Set-reset capability
