Parameters |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 1 day ago) |
Contact Plating |
Gold |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Weight |
141.690917mg |
Operating Temperature |
-55°C~125°C TA |
Packaging |
Tube |
Series |
74HC |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Type |
D-Type |
Additional Feature |
DUMMY VAL |
Subcategory |
FF/Latches |
Technology |
CMOS |
Voltage - Supply |
2V~6V |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Supply Voltage |
4.5V |
Base Part Number |
74HC174 |
Function |
Master Reset |
Output Type |
Non-Inverted |
Number of Elements |
1 |
Polarity |
Non-Inverting |
Supply Voltage-Max (Vsup) |
6V |
Supply Voltage-Min (Vsup) |
2V |
Number of Channels |
6 |
Number of Circuits |
7 |
Load Capacitance |
50pF |
Output Current |
5.2mA |
Number of Bits |
6 |
Clock Frequency |
35MHz |
Propagation Delay |
250 ns |
Quiescent Current |
8μA |
Turn On Delay Time |
13 ns |
Family |
HC/UH |
Logic Function |
D-Type, Flip-Flop |
Current - Output High, Low |
5.2mA 5.2mA |
Max I(ol) |
0.0052 A |
Max Propagation Delay @ V, Max CL |
28ns @ 6V, 50pF |
Trigger Type |
Positive Edge |
Input Capacitance |
10pF |
Power Supply Current-Max (ICC) |
0.08mA |
fmax-Min |
24 MHz |
Clock Edge Trigger Type |
Positive Edge |
Max Frequency@Nom-Sup |
20000000Hz |
Height |
1.75mm |
Length |
9.9mm |
Width |
3.91mm |
Thickness |
1.58mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
CD74HC174M Overview
The package is in the form of 16-SOIC (0.154, 3.90mm Width). As part of the package Tube, it is embedded. In the configuration, Non-Invertedis used as the output. This trigger is configured to use Positive Edge. Surface Mountis positioned in the way of this electronic part. The JK flip flop operates at 2V~6Vvolts. Temperature is set to -55°C~125°C TA. This logic flip flop is classified as type D-Type. It belongs to the 74HCseries of FPGAs. It should not exceed 35MHzin its output frequency. In total, it contains 1 elements. Terminations are 16. If you search by 74HC174, you will find similar parts. It is powered from a supply voltage of 4.5V. The input capacitance of this T flip flop is 10pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. In this case, the D flip flop belongs to the HC/UHfamily. A part of the electronic system is mounted in the way of Surface Mount. The electronic flip flop is designed with pins 16. The clock edge trigger type for this device is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. This flip flop is designed with 6 Bits. 6Vis the maximum supply voltage (Vsup). The supply voltage (Vsup) should be maintained above 2V for normal operation. Its superior flexibility is attributed to its use of 7 circuits. In addition to its maximum design flexibility, the output current of the T flip flop is 5.2mA. Quiescent current is consumed by the D latch in the amount of 8μA. Additionally, you may refer to the additional DUMMY VAL of the electronic flip flop. 6 channels are available.
CD74HC174M Features
Tube package
74HC series
16 pins
6 Bits
CD74HC174M Applications
There are a lot of Texas Instruments CD74HC174M Flip Flops applications.
- Consumer
- ATE
- QML qualified product
- Latch-up performance
- Data Synchronizers
- Instrumentation
- ESD protection
- 2 – Bit synchronous counter
- Registers
- Dynamic threshold performance