CD74HC374M96
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 4.5V |
| Base Part Number | 74HC374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 7.8mA |
| Number of Bits | 8 |
| Clock Frequency | 60MHz |
| Propagation Delay | 250 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 15 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max Propagation Delay @ V, Max CL | 28ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74HC374M96 Overview
The package is in the form of 20-SOIC (0.295, 7.50mm Width). As part of the package Cut Tape (CT), it is embedded. This output is configured with Tri-State, Non-Inverted. The trigger configured with it uses Positive Edge. Surface Mountmounts this electrical part. A 2V~6Vsupply voltage is required for it to operate. The operating temperature is -55°C~125°C TA. This D latch has the type D-Type. The FPGA belongs to the 74HC series. A frequency of 60MHzshould not be exceeded by its output. A total of 1elements are contained within it. There are 20 terminations,This D latch belongs to the family of 74HC374. Power is provided by a 4.5V supply. This JK flip flop has a 10pFfarad input capacitance. It belongs to the family of electronic devices known as HC/UH. Surface Mount mounts this electronic component. 20pins are included in its design. The clock edge trigger type for this device is Positive Edge. It is included in FF/Latches. This flip flop is designed with 8 Bits. As soon as Vsup reaches 6V, the maximum supply voltage is reached. Normally, the supply voltage (Vsup) should be kept above 2V. In order to achieve its superior flexibility, 8 circuits are used. Considering its reliability, this T flip flop is well suited for TR. A power supply of 2/6Vis required to operate it. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. It offers maximum design flexibility with its output current of 7.8mA. In order for the chip to function, it has 3output lines. It consumes 8μA current.
CD74HC374M96 Features
Cut Tape (CT) package
74HC series
20 pins
8 Bits
2/6V power supplies
CD74HC374M96 Applications
There are a lot of Texas Instruments CD74HC374M96 Flip Flops applications.
- Memory
- Patented noise
- Dynamic threshold performance
- Automotive
- Digital electronics systems
- Circuit Design
- Count Modes
- Memory
- Bounce elimination switch
- Single Up Count-Control Line
