CD74HC374M96E4
| Parameters | |
|---|---|
| Max Propagation Delay @ V, Max CL | 28ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 4.5V |
| Base Part Number | 74HC374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 7.8mA |
| Number of Bits | 8 |
| Clock Frequency | 60MHz |
| Propagation Delay | 250 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 15 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 7.8mA 7.8mA |
CD74HC374M96E4 Overview
The flip flop is packaged in a case of 20-SOIC (0.295, 7.50mm Width). As part of the package Tape & Reel (TR), it is embedded. As configured, the output uses Tri-State, Non-Inverted. It is configured with a trigger that uses Positive Edge. There is an electronic component mounted in the way of Surface Mount. A 2V~6Vsupply voltage is required for it to operate. -55°C~125°C TAis the operating temperature. It is an electronic flip flop with the type D-Type. FPGAs belonging to the 74HCseries contain this type of chip. You should not exceed 60MHzin its output frequency. In total, there are 1 elements. The number of terminations is 20. The 74HC374 family contains it. An input voltage of 4.5Vpowers the D latch. Its input capacitance is 10pFfarads. HC/UHis the family of this D flip flop. It is mounted by the way of Surface Mount. It is designed with 20 pins. This device has the clock edge trigger type of Positive Edge. It is part of the FF/Latchesbase part number family. There are 8bits in this flip flop. Vsup reaches 6V, the maximal supply voltage. A normal operating voltage (Vsup) should remain above 2V. In order to achieve its superior flexibility, 8 circuits are used. On the basis of its reliable performance, this D flip flop is well suited for use with TR. The power supply is 2/6V. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. With an output current of 7.8mA, it is possible to design the device in any way you want. There are 3 output lines on it. There is a consumption of 8μAof quiescent current from it.
CD74HC374M96E4 Features
Tape & Reel (TR) package
74HC series
20 pins
8 Bits
2/6V power supplies
CD74HC374M96E4 Applications
There are a lot of Texas Instruments CD74HC374M96E4 Flip Flops applications.
- Memory
- Dynamic threshold performance
- ATE
- Count Modes
- ESD performance
- Common Clocks
- Bounce elimination switch
- CMOS Process
- Reduced system switching noise
- Shift Registers
