CD74HC4016E
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Weight | 927.99329mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 170Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 4 |
| Supply Voltage | 4.5V |
| Base Part Number | 74HC4016 |
| Pin Count | 14 |
| Polarity | Non-Inverting |
| Number of Channels | 4 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 2V |
| Max Supply Current | 16μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 35 ns |
| Input Voltage (Max) | 6V |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 28 ns |
| -3db Bandwidth | 20MHz |
| On-State Resistance (Max) | 170Ohm |
| High Level Output Current | 25mA |
| Low Level Output Current | 25mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF |
| On-state Resistance Match-Nom | 10Ohm |
| Switch Circuit | SPST - NO |
| Channel-to-Channel Matching (ΔRon) | 8.5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 38ns |
| Switch-off Time-Max | 29ns |
| Voltage - Supply, Single (V+) | 2V~10V |
| Normal Position | NO |
| Signal Current-Max | 0.025A |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74HC4016E Overview
Presented in 14-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tube is used. Multiplexers like this are mounted in the Through Hole position. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operating temperature extended to -55°C~125°C TA. A total of 14 terminations have been recorded. Due to its 4 channels, the electrical component produces high-quality output. When the electronic component is given a voltage of 4.5V, it should be turned on and run. This electrical component is included in the 14 series of products. Circuits based on SPST - NO switching are used to construct these analog switch ics. Try searching for 74HC4016 variants of the analog switch ic. It has an internal resistance of 170Ohm. You can find the functions of the 14 pins in the datasheets. Multiplexer or Switches is a typical switch device. Multiplexers should not be powered above 10V in normal situations. Analog switch ics with Single supply type are cost-effective. 2V should be the lowest voltage fed to the electronic component. This analog switch requires a voltage of 2V~10V to drain from a single voltage supply. Put voltage above 16μA on the multiplexer to cause damage. 200MHz-bandwidths can be used to transfer data between multiplexers.
CD74HC4016E Features
4 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 20MHz
Bandwidth: 200MHz
CD74HC4016E Applications
There are a lot of Texas Instruments CD74HC4016E Analog Switches & Multiplexers ICs applications.
- Optical Applications
- Cellular phones
- Audio signal routing
- Power routing
- Microprocessor Controlled Analog Systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Ultrasound
- Multi-Line E1 Interface Cards
- E1 Network Equipment
- Digital access cross connects
