Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
14-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
14 |
Weight |
57.209338mg |
Operating Temperature |
-55°C~125°C TA |
Packaging |
Tape & Reel (TR) |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
Resistance |
170Ohm |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
NOT SPECIFIED |
Number of Functions |
4 |
Supply Voltage |
4.5V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
Base Part Number |
74HC4016 |
Output |
SEPARATE OUTPUT |
Pin Count |
14 |
Qualification Status |
Not Qualified |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
10V |
Min Supply Voltage |
2V |
Max Supply Current |
16μA |
Throw Configuration |
SPST |
Turn On Delay Time |
190 ns |
Supply Type |
Single |
Turn-Off Delay Time |
145 ns |
-3db Bandwidth |
20MHz |
On-State Resistance (Max) |
170Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
62 dB |
Current - Leakage (IS(off)) (Max) |
100nA |
Channel Capacitance (CS(off), CD(off)) |
10pF |
On-state Resistance Match-Nom |
10Ohm |
Switch Circuit |
SPST - NO |
Channel-to-Channel Matching (ΔRon) |
8.5 Ω |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
38ns |
Switch-off Time-Max |
29ns |
Voltage - Supply, Single (V+) |
2V~10V |
Normal Position |
NO |
Height Seated (Max) |
1.2mm |
Length |
5mm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
CD74HC4016PWR Overview
Packed in 14-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. The advanced packaging method Tape & Reel (TR) provides high reliability. The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Temperatures around -55°C~125°C TA are extended for operation. The total number of terminations is 14. A high-quality output is provided by the electrical component's 1 channels. With a 4.5V voltage supply, the electrical component should be turned on and run. A total of 14 pins are injected into the body of the electronic part. A SPST - NO switching circuit is used for these analog switches. Circuits number 4 make up this analogue multiplexer. 74HC4016 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 170Ohm. The functions of 14 pins can be found in the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Users should never supply a voltage higher than 10V to a switch device. A cost-effective Single supply type analogue multiplexer. It is recommended that the electrical component receives a voltage of 2V. A voltage of 2V~10V is required for this switch device, which drains from a single voltage source. When the digital multiplexer is charged above 16μA, damage can occur. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.
CD74HC4016PWR Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 20MHz
CD74HC4016PWR Applications
There are a lot of Texas Instruments CD74HC4016PWR Analog Switches & Multiplexers ICs applications.
- FTTH
- Industrial and process control systems
- PDH Multiplexers
- RGB switches
- DSLAMs
- Digital Cross-Connects
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Medical Instrumentation
- PCMCIA cards
- Fault Tolerant Systems