CD74HC4016PWRE4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 57.209338mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 170Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 4 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HC4016 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 2V |
| Max Supply Current | 16μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 190 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 145 ns |
| -3db Bandwidth | 20MHz |
| On-State Resistance (Max) | 170Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF |
| On-state Resistance Match-Nom | 10Ohm |
| Switch Circuit | SPST - NO |
| Channel-to-Channel Matching (ΔRon) | 8.5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 38ns |
| Switch-off Time-Max | 29ns |
| Voltage - Supply, Single (V+) | 2V~10V |
| Normal Position | NO |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74HC4016PWRE4 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 14-TSSOP (0.173, 4.40mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operating temperature extended to -55°C~125°C TA. In total, there have been 14 terminations. As a result of its 1 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 4.5V voltage supply. It is injected into the electrical part body with 14 pins. Unlike digital switches, these are based on SPST - NO switching circuits. The multiplexer consists of 4 circuits. Search with 74HC4016 if you are looking for analog multiplexer variants. As far as internal resistance is concerned, it has 170Ohm. Datasheets for 14 pin functions are available upon request. It is a typical Multiplexer or Switches analog multiplexer. It is generally not recommended to supply a voltage higher than 10V to the switch device in normal circumstances. A analog switch ic that has a cost-effective Single supply type. 2V is the lowest voltage that should be fed to the electronic electronic part. Using a single voltage supply, this switch device consumes 2V~10V volts. If you put voltage higher than 16μA on the digital multiplexer, damage may occur. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
CD74HC4016PWRE4 Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 20MHz
CD74HC4016PWRE4 Applications
There are a lot of Texas Instruments CD74HC4016PWRE4 Analog Switches & Multiplexers ICs applications.
- Mechanical reed relay replacement
- ATM
- New designs requiring multiplexer functions
- Industrial control systems
- Switching Systems
- PBX interfaces
- Battery Powered Instruments
- Precision instrumentation
- Private Branch Exchange (PBX)
- Video switching
