CD74HC4052PWG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 61.887009mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 130Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HC4052 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 8 |
| Number of Circuits | 2 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Nominal Supply Current | 16μA |
| Number of Bits | 4 |
| Throw Configuration | 4PST |
| Propagation Delay | 4 ns |
| Turn On Delay Time | 325 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~6V ±1V~5V |
| Supply Type | Dual, Single |
| Bandwidth | 185MHz |
| Neg Supply Voltage-Nom (Vsup) | -4.5V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 5V |
| On-State Resistance (Max) | 130Ohm |
| Min Dual Supply Voltage | 1V |
| High Level Output Current | 25mA |
| Dual Supply Voltage | 3V |
| Low Level Output Current | 25mA |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 200nA |
| Channel Capacitance (CS(off), CD(off)) | 12pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SP4T |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Length | 5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74HC4052PWG4 Overview
The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). High reliability is provided by advanced packaging method Tube. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a ratio of 4:1. An extended operating temperature of -55°C~125°C TA degrees Celsius. There are 16 terminations totally. As a result of its 8 channels, this electronic component provides high-quality output. A 4.5V voltage supply should turn on and run the electronic component. There is an electrical component included in the 16 series. The analog switch ics are built using SP4T switching circuits. The circuits in this analogue multiplexer number 2. Try searching for 74HC4052 variants of the analog switch ic. This digital multiplexer has 130Ohm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. normally, users should not supply switches with voltages higher than 6V. The analog switch ic is of the Dual, Single supply type and is cost-effective. There should be 2V voltage fed to the electrical part below 2V. Despite this switch's dual supply capability, its voltage should not exceed 5V. A dual power supply should have at least 1V voltage attached. A DIFFERENTIAL MULTIPLEXER analog IC is integrated into the board. There are 185MHz bandwidths for data transfer. 4-bit operation is possible.
CD74HC4052PWG4 Features
8 Channels
Switch Circuit: SP4T
Bandwidth: 185MHz
4-Bit
CD74HC4052PWG4 Applications
There are a lot of Texas Instruments CD74HC4052PWG4 Analog Switches & Multiplexers ICs applications.
- PBXs
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Remote wireless modules
- Audio and video routing
- Fiber to the Home
- Video switching
- Fault Tolerant Systems
- T1/E1 Terminals
- ATM
- FTTH
