CD74HC4066E
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Gold |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Weight | 927.99329mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 70Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 4 |
| Supply Voltage | 4.5V |
| Base Part Number | 74HC4066 |
| Pin Count | 14 |
| Polarity | Non-Inverting |
| Number of Channels | 4 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 2V |
| Max Supply Current | 16μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 15 ns |
| Input Voltage (Min) | 2V |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Rise Time | 400ns |
| Turn-Off Delay Time | 30 ns |
| On-State Resistance (Max) | 70Ohm |
| High Level Output Current | 25mA |
| Low Level Output Current | 25mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NO |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -72dB @ 1MHz |
| Switching | MAKE-BEFORE-BREAK |
| Voltage - Supply, Single (V+) | 2V~10V |
| Normal Position | NO |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74HC4066E Overview
Presented in 14-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. Advanced packaging method Tube is used to provide high reliability. Through Hole is where this multiplexer is located. 1:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around -55°C~125°C TA. Totally, there are 14 terminations. As a result of its 4 channels, this electronic component provides high-quality output. A 4.5V voltage supply should turn on and run the electronic component. An electrical component like this is included in the 14 series. Circuits based on SPST - NO switching are used to construct these analog switch ics. Try searching for 74HC4066 variants of the analog switch ic. Internally, this switch multiplexer has a resistance of 70Ohm. Please refer to the datasheets for 14 pins functions. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 10V. Analogue multiplexers of the Single supply type that are cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. A voltage of 2V~10V is required to drain this analog switch from a single voltage supply. Put voltage above 16μA on the multiplexer to cause damage. 200MHz bandwidths enable data to be transferred.
CD74HC4066E Features
4 Channels
Switch Circuit: SPST - NO
Bandwidth: 200MHz
CD74HC4066E Applications
There are a lot of Texas Instruments CD74HC4066E Analog Switches & Multiplexers ICs applications.
- Microprocessor controlled systems
- Residential Gateways, Home Gateway/Router
- Data Acquisition Systems
- Channel Banks
- Mechanical reed relay replacement
- Industrial and process control systems
- Intelligent PBX
- Multiplexers
- Precision instrumentation
- Battery Powered Instruments
