Parameters |
Contact Plating |
Gold |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
14-SOIC (0.154, 3.90mm Width) |
Number of Pins |
14 |
Weight |
129.387224mg |
Operating Temperature |
-55°C~125°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e4 |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
ECCN Code |
EAR99 |
Resistance |
70Ohm |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
4.5V |
Terminal Pitch |
1.27mm |
Base Part Number |
74HC4066 |
Pin Count |
14 |
Polarity |
Non-Inverting |
Number of Channels |
4 |
Max Supply Voltage |
10V |
Min Supply Voltage |
2V |
Max Supply Current |
16μA |
Throw Configuration |
SPST |
Turn On Delay Time |
100 ns |
Input Voltage (Min) |
2V |
Supply Type |
Single |
Bandwidth |
200MHz |
Turn-Off Delay Time |
150 ns |
On-State Resistance (Max) |
70Ohm |
High Level Output Current |
25mA |
Low Level Output Current |
25mA |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
100nA |
Channel Capacitance (CS(off), CD(off)) |
5pF |
On-state Resistance Match-Nom |
1Ohm |
Switch Circuit |
SPST - NO |
Channel-to-Channel Matching (ΔRon) |
500m Ω |
Crosstalk |
-72dB @ 1MHz |
Switching |
MAKE-BEFORE-BREAK |
Switch-on Time-Max |
30ns |
Voltage - Supply, Single (V+) |
2V~10V |
Normal Position |
NO |
Height |
1.58mm |
Length |
8.65mm |
Width |
3.91mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
CD74HC4066M96G4 Overview
Presented in 14-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, you'll find this switch device. 1:1 is the number of circuits in the multiplexer and demultiplexer. An extended operating temperature of -55°C~125°C TA degrees Celsius. 14 terminations have been made so far. The electronic part provides high-quality output because it has 4 channels. An 4.5V voltage supply should allow the electrical part to be turned on and run. A key feature of the 14 series is the inclusion of this electronic part as part of its design. A SPST - NO switching circuit is used for these analog switches. 74HC4066 can be used to search for analog multiplexer variants. In this multiplexer, the internal resistance is 70Ohm. Please refer to the datasheets for 14 pins functions. Theswitch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 10V volts for the multiplexer. Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 2V. An analogue multiplexer drains from a single voltage supply at 2V~10V. A digital multiplexer may suffer damage if voltage is applied above 16μA. There are 200MHz bandwidths for data transfer.
CD74HC4066M96G4 Features
4 Channels
Switch Circuit: SPST - NO
Bandwidth: 200MHz
CD74HC4066M96G4 Applications
There are a lot of Texas Instruments CD74HC4066M96G4 Analog Switches & Multiplexers ICs applications.
- Audio and video signal routing
- Precision test equipment
- Battery Powered Instruments
- PCMCIA cards
- Cell phones
- Communications systems
- Cross Connects
- Voice over IP/DSL – Integrated Access Devices, Smart
- Sample-and-hold systems
- T1/E1 Terminals