CD74HC4066MT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Termination | SMD/SMT |
| Resistance | 70Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HC4066 |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Max Output Current | 25mA |
| Polarity | Non-Inverting |
| Number of Channels | 4 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 2V |
| Max Supply Current | 16μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 100 ns |
| Input Voltage (Min) | 2V |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 150 ns |
| On-State Resistance (Max) | 70Ohm |
| High Level Output Current | 25mA |
| Low Level Output Current | 25mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NO |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -72dB @ 1MHz |
| Switching | MAKE-BEFORE-BREAK |
| Switch-on Time-Max | 30ns |
| Voltage - Supply, Single (V+) | 2V~10V |
| Normal Position | NO |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74HC4066MT Overview
Presented in 14-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -55°C~125°C TA extended. In total, there are 14 terminations. A high-quality output is provided by the electrical component's 4 channels. If the voltage supply is 4.5V volts, the electrical component should be turned on and run. A key feature of the 14 series is the inclusion of this electronic part as part of its design. Unlike digital switches, these are based on SPST - NO switching circuits. Try searching for the analog switch ic with 74HC4066 if you are looking for variants. In this multiplexer, the internal resistance is 70Ohm. For details about the functions of 14 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. Users shouldn't supply more than 10V voltage to the switch device. The digital multiplexer has a low cost Single supply. 2V is the lowest voltage that should be fed to the electronic electronic part. The voltage required by this switch device is 2V~10V, draining from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 16μA. It is possible to transfer data over a 200MHz-bandwidth.
CD74HC4066MT Features
4 Channels
Switch Circuit: SPST - NO
Bandwidth: 200MHz
CD74HC4066MT Applications
There are a lot of Texas Instruments CD74HC4066MT Analog Switches & Multiplexers ICs applications.
- Avionics and Military Systems
- Multi-Line E1 Interface Cards
- Mechanical reed relay replacement
- Frame Relay Equipment
- High reliability control systems
- Automotive applications
- Fiber In The Loop (FITL)
- Isolation
- Central office
- Imaging
