Parameters |
Packaging |
Tube |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
ECCN Code |
EAR99 |
Resistance |
70Ohm |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
4.5V |
Base Part Number |
74HC4066 |
Pin Count |
14 |
Polarity |
Non-Inverting |
Number of Channels |
4 |
Max Supply Voltage |
10V |
Min Supply Voltage |
2V |
Max Supply Current |
16μA |
Throw Configuration |
SPST |
Turn On Delay Time |
15 ns |
Input Voltage (Min) |
2V |
Supply Type |
Single |
Bandwidth |
200MHz |
Turn-Off Delay Time |
30 ns |
On-State Resistance (Max) |
70Ohm |
High Level Output Current |
25mA |
Low Level Output Current |
25mA |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
100nA |
Channel Capacitance (CS(off), CD(off)) |
5pF |
On-state Resistance Match-Nom |
1Ohm |
Switch Circuit |
SPST - NO |
Channel-to-Channel Matching (ΔRon) |
500m Ω |
Crosstalk |
-72dB @ 1MHz |
Switching |
MAKE-BEFORE-BREAK |
Voltage - Supply, Single (V+) |
2V~10V |
Drain to Source Resistance |
25Ohm |
Normal Position |
NO |
Height |
1.2mm |
Length |
5mm |
Width |
4.4mm |
Thickness |
1mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 2 days ago) |
Contact Plating |
Gold |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
14-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
14 |
Weight |
57.209338mg |
Operating Temperature |
-55°C~125°C TA |
CD74HC4066PW Overview
The electronic component is convenient to ship overseas because it is packed in a 14-TSSOP (0.173, 4.40mm Width). This high-reliability packaging method uses advanced packaging methods Tube. Surface Mount is where this multiplexer is located. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operational temperature extended around -55°C~125°C TA. Total terminations are 14. By its 4 channels, the electronic component provides high-quality output. An 4.5V voltage supply should allow the electrical part to be turned on and run. An electrical component of this type can be found in the 14 series. Based on SPST - NO switching circuits, these analog multiplexers work. Search with 74HC4066 if you are looking for analog multiplexer variants. The internal resistance of this digital multiplexer is 70Ohm. The functions of 14 pins can be found in the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 10V to the switch device in normal circumstances. A analog switch ic that has a cost-effective Single supply type. There should be 2V voltage fed to the electrical part below 2V. A voltage of 2V~10V is required to drain this analog switch from a single voltage supply. A voltage higher than 16μA may cause damage to the switch multiplexer. A 200MHz-bandwidth can be used for data transfer. It has a Drain to Source resistance of 25Ohm ohms.
CD74HC4066PW Features
4 Channels
Switch Circuit: SPST - NO
Bandwidth: 200MHz
Drain-to-Source resistance: 25Ohm
CD74HC4066PW Applications
There are a lot of Texas Instruments CD74HC4066PW Analog Switches & Multiplexers ICs applications.
- Channel Banks
- E1 Network Equipment
- Relay Replacement
- Frame Relay Equipment
- RGB switches
- Voice over IP/DSL – Integrated Access Devices, Smart
- Remote wireless modules
- Video signal routing
- Cell phones
- FTTH