CD74HC4066PWR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 57.209338mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 70Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 4.5V |
| Base Part Number | 74HC4066 |
| Pin Count | 14 |
| Polarity | Non-Inverting |
| Number of Channels | 4 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 2V |
| Max Supply Current | 16μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 15 ns |
| Input Voltage (Min) | 2V |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 30 ns |
| On-State Resistance (Max) | 70Ohm |
| High Level Output Current | 25mA |
| Low Level Output Current | 25mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NO |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -72dB @ 1MHz |
| Switching | MAKE-BEFORE-BREAK |
| Voltage - Supply, Single (V+) | 2V~10V |
| Drain to Source Resistance | 70Ohm |
| Normal Position | NO |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74HC4066PWR Overview
This electronic part is conveniently packaged in 14-TSSOP (0.173, 4.40mm Width), making it easy to ship abroad. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. Multiplexer and demultiplexer circuits have a number 1:1. Operation at a temperature around -55°C~125°C TA. Totally, there are 14 terminations. High-quality output is provided by the electronic component's 4 channels. An 4.5V voltage supply should allow the electrical part to be turned on and run. There is an electrical component included in the 14 series. A SPST - NO switching circuit is used for these analog switches. Look for analog switch ic variants by searching with 74HC4066. In this multiplexer, the internal resistance is 70Ohm. To find out what the functions of 14 pins are, please refer to their datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 10V to the switch device in normal circumstances. The digital multiplexer has a low cost Single supply. It is recommended to use 2V as the lowest voltage for the electrical part. Using a single voltage supply, this switch device consumes 2V~10V volts. If put voltage greater than 16μA on the device, damage may be caused to the analogue multiplexer. This switch operates within the bandwidth of 200MHz. It has a Drain to Source resistance of 70Ohm ohms.
CD74HC4066PWR Features
4 Channels
Switch Circuit: SPST - NO
Bandwidth: 200MHz
Drain-to-Source resistance: 70Ohm
CD74HC4066PWR Applications
There are a lot of Texas Instruments CD74HC4066PWR Analog Switches & Multiplexers ICs applications.
- Digital access cross connects
- Imaging
- Public switching systems
- SONET
- Channel Banks
- FTTH
- Cable Modem
- Medical systems
- CSU
- Mechanical reed relay replacement
