CD74HC4066PWT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 57.209338mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Termination | SMD/SMT |
| Resistance | 70Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 4.5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HC4066 |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Max Output Current | 25mA |
| Number of Channels | 4 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 2V |
| Max Supply Current | 16μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 100 ns |
| Input Voltage (Min) | 2V |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 150 ns |
| On-State Resistance (Max) | 70Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NO |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -72dB @ 1MHz |
| Switching | MAKE-BEFORE-BREAK |
| Switch-on Time-Max | 30ns |
| Voltage - Supply, Single (V+) | 2V~10V |
| Normal Position | NO |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74HC4066PWT Overview
The electronic part can be shipped overseas conveniently because it is packaged in 14-TSSOP (0.173, 4.40mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. The operating temperature is extended to around -55°C~125°C TA. In total, there are 14 terminations. Due to its 4 channels, the electrical component produces high-quality output. When the electronic component is given a voltage of 4.5V, it should be turned on and run. As part of the design of the 14 series, this electronic part has been incorporated into the system. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Try searching for 74HC4066 variants of the analog switch ic. A 70Ohm internal resistance characterizes this multiplexer. Please refer to the datasheets for 14 pins functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users should never supply a voltage higher than 10V to a switch device. The analog switch ic is of the Single supply type and is cost-effective. 2V is the lowest voltage the electrical component should receive. A voltage of 2V~10V is required for this switch device, which drains from a single voltage source. If you put voltage higher than 16μA on the digital multiplexer, damage may occur. There are 200MHz bandwidths for data transfer.
CD74HC4066PWT Features
4 Channels
Switch Circuit: SPST - NO
Bandwidth: 200MHz
CD74HC4066PWT Applications
There are a lot of Texas Instruments CD74HC4066PWT Analog Switches & Multiplexers ICs applications.
- Industrial and process control systems
- 65 V DACs
- Precision data acquisition
- Remote Powered Equipment
- Audio and video signal routing
- Digital access cross connects
- Relay Replacement
- SDH
- USB 1.1 signal switching circuits
- Channel Banks
