CD74HC564M96
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 4.5V |
| Base Part Number | 74HC564 |
| Function | Standard |
| Output Type | Tri-State, Inverted |
| Number of Elements | 1 |
| Polarity | Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 7.8mA |
| Number of Bits | 8 |
| Clock Frequency | 60MHz |
| Propagation Delay | 250 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 13 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max Propagation Delay @ V, Max CL | 28ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74HC564M96 Overview
In the form of 20-SOIC (0.295, 7.50mm Width), it has been packaged. There is an embedded version in the package Tape & Reel (TR). T flip flop uses Tri-State, Invertedas its output configuration. Positive Edgeis the trigger it is configured with. It is mounted in the way of Surface Mount. The supply voltage is set to 2V~6V. It is at -55°C~125°C TAdegrees Celsius that the system is operating. There is D-Type type of electronic flip flop associated with this device. JK flip flop belongs to the 74HCseries of FPGAs. You should not exceed 60MHzin the output frequency of the device. In total, it contains 1 elements. 20terminations have occurred. This D latch belongs to the family of 74HC564. Power is provided by a 4.5V supply. JK flip flop input capacitance is 10pF farads. In terms of electronic devices, this device belongs to the HC/UHfamily of devices. This electronic part is mounted in the way of Surface Mount. This board is designed with 20pins on it. There is a clock edge trigger type of Positive Edgeon this device. This part is included in FF/Latches. There are 8bits in its design. It reaches 6Vwhen the maximum supply voltage (Vsup) is applied. Normally, the supply voltage (Vsup) should be above 2V. Using 8 circuits, it is highly flexible. Considering the reliability of this T flip flop, it is well suited for TR. A total of 2/6V power supplies are needed to run it. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. In addition to its maximum design flexibility, the output current of the T flip flop is 7.8mA. In order to operate, the chip has 3 output lines. 8μAquiescent current consumed.
CD74HC564M96 Features
Tape & Reel (TR) package
74HC series
20 pins
8 Bits
2/6V power supplies
CD74HC564M96 Applications
There are a lot of Texas Instruments CD74HC564M96 Flip Flops applications.
- Data Synchronizers
- Control circuits
- Count Modes
- Event Detectors
- Power down protection
- ATE
- Latch-up performance
- Latch
- Modulo – n – counter
- QML qualified product
