CD74HC73M96G4
| Parameters | |
|---|---|
| Contact Plating | Gold |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 14 |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 4.5V |
| Frequency | 60MHz |
| Pin Count | 14 |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Load Capacitance | 50pF |
| Current - Output | 5.2mA |
| Number of Bits | 2 |
| Propagation Delay | 160 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 13 ns |
| Family | HC/UH |
| Logic Function | JK-Type |
| Logic IC Type | J-K FLIP-FLOP |
| Max I(ol) | 0.004 A |
| High Level Output Current | -5.2mA |
| Low Level Output Current | 5.2mA |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Negative Edge |
| Height | 1.58mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
CD74HC73M96G4 Overview
It is packaged in the way of SOIC. A total of 2elements are contained within it. The number of terminations is 14. Power is supplied from a voltage of 4.5V volts. This D flip flop belongs to the family of HC/UH. There is an electronic part that is mounted in the way of Surface Mount. With its 14pins, it is designed to work with most electronic flip flops. In this device, the clock edge trigger type is Negative Edge. It is included in FF/Latches. Flip flops designed with 2bits are used in this part. Due to its reliability, this T flip flop is well suited for TAPE AND REEL. It is designed with 1 output lines. As a result, it consumes 4μA of quiescent current without being affected by external factors. It is set to -5.2mAfor the high level output current. In the low level output current setting, 5.2mAis used. If the operating temperature is lower than 125°C, it is recommended. If the operating temperature is higher than -55°C, the system should operate properly. It operates with the minimal supply voltage of 2V. 6Vis the maximum supply voltage it supports. 60MHzis the maximum frequency that can be achieved. It uses the logic IC J-K FLIP-FLOP. It is equipped with 2 Functions . 14pins are available on this JK flip flop. Its output current of 5.2mA allows for maximum design flexibility.
CD74HC73M96G4 Features
14 pins
2 Bits
2 Functions
14 pin count
CD74HC73M96G4 Applications
There are a lot of Texas Instruments CD74HC73M96G4 Flip Flops applications.
- ESD protection
- Counters
- Common Clocks
- Functionally equivalent to the MC10/100EL29
- Test & Measurement
- Convert a momentary switch to a toggle switch
- Control circuits
- Memory
- Modulo – n – counter
- Single Up Count-Control Line
