CD74HC74MT
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 4.5V |
| Base Part Number | 74HC74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Clock Frequency | 50MHz |
| Propagation Delay | 175 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 14 ns |
| Family | HC/UH |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 30ns @ 6V, 50pF |
| Prop. Delay@Nom-Sup | 53 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
CD74HC74MT Overview
The package is in the form of 14-SOIC (0.154, 3.90mm Width). It is contained within the Tape & Reel (TR)package. The output it is configured with uses Differential. It is configured with a trigger that uses a value of Positive Edge. The electronic part is mounted in the way of Surface Mount. A 2V~6Vsupply voltage is required for it to operate. In this case, the operating temperature is -55°C~125°C TA. This logic flip flop is classified as type D-Type. It is a type of FPGA belonging to the 74HC series. There should be no greater frequency than 50MHzon its output. There are 14 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. Members of the 74HC74family make up this object. The power source is powered by 4.5V. The input capacitance of this T flip flop is 10pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. A device of this type belongs to the family of HC/UH. It is mounted by the way of Surface Mount. This board is designed with 14pins on it. Its clock edge trigger type is Positive Edge. This device is part of the FF/Latchesbase part number family. It reaches 6Vwhen the maximum supply voltage (Vsup) is applied. Normally, the supply voltage (Vsup) should be kept above 2V. To achieve this superior flexibility, 2 circuits are used. As a result of its reliable performance, this T flip flop is suitable for TR. It offers maximum design flexibility with its output current of 5.2mA. To operate, the chip has a total of 1 output lines. It consumes 4μA current.
CD74HC74MT Features
Tape & Reel (TR) package
74HC series
14 pins
CD74HC74MT Applications
There are a lot of Texas Instruments CD74HC74MT Flip Flops applications.
- Computers
- Divide a clock signal by 2 or 4
- Bounce elimination switch
- Consumer
- Guaranteed simultaneous switching noise level
- Computing
- Shift Registers
- Load Control
- Registers
- CMOS Process
