CD74HCT174M96G4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Additional Feature | DUMMY VAL |
| Subcategory | FF/Latch |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74HCT174 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Load Capacitance | 50pF |
| Number of Bits | 6 |
| Clock Frequency | 25MHz |
| Propagation Delay | 40 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 17 ns |
| Family | HCT |
| Current - Output High, Low | 4mA 4mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 40ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Power Supply Current-Max (ICC) | 0.08mA |
| Number of Input Lines | 6 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.75mm |
| Length | 9.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74HCT174M96G4 Overview
The package is in the form of 16-SOIC (0.154, 3.90mm Width). There is an embedded version in the package Tape & Reel (TR). There is a Non-Invertedoutput configured with it. This trigger is configured to use Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis required for its operation. It is at -55°C~125°C TAdegrees Celsius that the system is operating. Logic flip flops of this type are classified as D-Type. JK flip flop is a part of the 74HCTseries of FPGAs. Its output frequency should not exceed 25MHz. There are 1 elements in it. Currently, there are 16 terminations. If you search by 74HCT174, you will find similar parts. The D flip flop is powered by a voltage of 5V . Its input capacitance is 10pF farads. It is a member of the HCTfamily of D flip flop. The electronic part is mounted in the way of Surface Mount. Basically, it is designed with a set of 16 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The part you are looking for is included in FF/Latch. Flip flops designed with 6bits are used in this part. Considering its reliability, this T flip flop is well suited for TR. The D latch runs on a voltage of 5V volts. For high efficiency, the supply voltage should be set to 5V. There are 6 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. In terms of quiescent current, it consumes 8μA . Furthermore, it has DUMMY VALas a characteristic.
CD74HCT174M96G4 Features
Tape & Reel (TR) package
74HCT series
16 pins
6 Bits
5V power supplies
CD74HCT174M96G4 Applications
There are a lot of Texas Instruments CD74HCT174M96G4 Flip Flops applications.
- Buffered Clock
- Divide a clock signal by 2 or 4
- 2 – Bit synchronous counter
- Matched Rise and Fall
- Convert a momentary switch to a toggle switch
- ESD protection
- Memory
- Clock pulse
- Test & Measurement
- Shift registers
